Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I've successfully setup a development environment for nRF Connect and Zephyr on windows (VS Code extension) where I can build, debug and flash code to my board...
The nRF52833 isn't supported Bluetooth low energy by nRF Connect for Desktop as list device in link https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfconnect_ble...
Hi, I'm working on nRF52840-DK board and NCS SDK-v1.7.0 on Windows with Visual Studio Code.
We want to add support for Image validation for imaged signed with ECC curve...
Hello,
I have nRF Connect Desktop v3.9.1 for MacOS installed. I am trying to run the "Bluetooth Low Energy" utility using a nRF52840 dongle.
If the only device connected...
Hello
I was trying to get this example ble_app_template to work but it seems like it doesn't, the code is executed on the ic since I was uploading some code to blink a light...
Hi,
I have a question about running a secure service that does RSA encryption and decryption in SPM using mbedTLS.
I am using SEGGER Embedded Studio for ARM (Nordic Edition...
Hello all, Currently I am developing a code in which a central (nRF52840) scans and reads adverisement packets from 2 beacons (no connection required). I decided to use an...
Using nRF52832, I've got some firmware that uses NFC pins (9 & 10) without problem, using CONFIG_NFCT_PINS_AS_GPIOS.
I'm now trying to replicate this using nRF52833, and...
I am working with the nRF52840 under Zephyr to develop some wireless sensors. The issue I am having I build a test module using the nrf/samples/light. This running on the...
Hello,
I've been experimenting with nRF Connect SDK and compiling a program which supports provisioner mode, provisioning and direction finding.
Everything compiles and...
Hi everyone,
I work with an nrf52840 and SDK15.3.0 and SD 140-6.1.1
I have a board with two micro controler, one nrf52840 and one STM32.
I want to know if it is possible...
Hi
I need to do DFU OTA for my Custom board. So, I need to Know the procedures which I need to follow for nrf5340 and how can I do that on NRF Connect SDK. Kindly help me...
i have no idea on how to read the device id of the qspi please guide me to do so i have gone through the qspi example there could not any instructions to read the device id...
Good day!
There is now way to restart dfu_mcuboot with
CONFIG_DFU_TARGET_STREAM_SAVE_PROGRESS
Checkout:
dfu_target.c
next dfu_target_mcu_boot.c
and finally...
I've been developing in the following environment:
Windows 10
NRF Connect for Desktop
with few problems for the past six months.
On Friday 12/10 I was suddenly unable...
