Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
I am trying to edit my bootloader (buttonless USB DFU).
I want to add a button to exit the bootloader and return to the app.
The problem is that the gpiote interrupt...
Hi Team,
We are on the Pre-Production stage of our Product, which uses the nRF52840 (forBLE) with the FEM nrf21540(new)
We are aiming to get power out of 20dBm.
To get...
I observe issues when trying to use the datetime lib on the board qemu_x86.
I get the following page fault:
This is reproducible and happens shorty after successfully...
Hello all,
I am migrating our FW NRF52832 from SDK11 to SDK17. (Actually I am starting from scratch on 17). Here I have two characteristics with only read properties (e...
To the kind attention of Nordic support team,
About nRF52833 product specifications (8. recommended operating conditions)
"Note: The on-chip power-on reset circuitry...
Hi,
I'm trying to run a pc-ble-driver on Arm64 arc
I've compiled the pc-ble-driver to arm 64 from this release: ARM64-linux pc-ble-driver origin/release/4.1.2
I used...
Hi,
I'm currently working on a way to connect raspberry pi as a gateway into the nrfcloud. For this case, I used nrfcloud/gateway-raspberry-pi. Neverless, when I tried to...
I am developing a product using nRF9160 and found the power consumption is higher than the datasheet. So I want to use Matlab ti simulate the circuit to see where the error...
I am currently trying to implement a Thread functionality on an nRF Dongle connected to a windows machine. Its intent is to be able to recieve messages from other thread components...
Hello Nordic team,
I have a nrf9160 powered from a 3.8v bench supply.
I also have a usb to uart cable , with uart wires going into NRF9160. Usb side, plugged into my computer...
Hi
1、 The following table does not indicate whether the QDID belongs to 5.1 or 5.2.Are the QDIDs of softdevice classified as Bluetooth 5.1 or 5.2?
2、The following qdid...
Hi all!
I flashed and got both SoftDevice s130 and the example code onto my nRF51802 without prior modifications.
I flashed softdevice according to: https://infocenter...
Dear Nordic Team,
Hope you all are doing fine.
I have the NRF52-DK based on the NRF52832 BLE IC from Nordic. I wanted to implement a basic BLE Beacon that broadcasts continuously...
Hello,
I am starting to work on a sample project, wherein I need to replace the existing "main.c" file I have with "main.cpp", by copying the contents of "main.c" into...
