dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello, I need a reference PCB layout for the nRF52810-CAAA WLCSP-33 chip. There doesn't seem to be a reference layout for this specific chip. Furthermore it differs from the...
Hi everyone,
I have a couple of Laird BL653 boards which use the nRF52833 chipset. They have SoftDevice S140 v7.0.1 on them and I'm using the nRF Mesh v3.1.4 for IOS. The...
On an NRF52811 (and I've had a similar problem on a 52833) I'm unable to use the NVS subsystem. Everything inits fine but there is a fault when writing to NV. If BT is disabled...
Hi Nordic team,
We have tried using Bluetooth peripheral HID keyboard example from nRF5 SDK and found an interesting problem.
In our setup, nRF52840DK is running the provided...
Hello all,
I have trouble reading saadc data with an amplitude of 10 µV - 100 µV with a sampling rate of 1K Hz by using nrf52832. I was wondering if I could get advice/help...
Hi,
The code is working normally, but when I include ble_radio_notification_init functionality. Then it crashes (hardfaults), on some boards not all.
[19:18:40.550]...
Hello.
We are migrating from SEGGER Embedded Studio (SES) to IAR Embedded Workbench (IAR). SES used Printf as a comment display and output it to the Terminal Emulator. I...
I've previously used Getting Started Assistant to install nRF Connect SDK 1.5.0 on macos and managed to get a complete and functional install.
I'm now trying the new Toolchain...
HI,
I have few queries regarding nRF52805.
Is there any specific pin configuration required to enter nRF52805 in to programming mode?
What is Adverting connectable...
Hello. I am conducting experiments with data transmission via the Enhanced ShockBurst protocol with BMD-340 modules. Transmission parameters: 2 Mbit radio channel speed, 512...
Hello Sirs
I want to use the serial port of nrf5340-Dk to get some serial data from a sensor and transmit this
data Via a peripheral connectable config by nrf5340-Dk ...
I'm trying to access an SD card with FAT_FS, with no success. I hooked an analyser to the SPI, but it's completely dead. I'm using NCS v1.6.0.
Is there something...
I am very new to BLE development, and am building my application on top of the ble_central\ble_app_uart_c example.
I have this tag defined at the start, with the other global...
Dear Nordic Engineers
Our customer uses NRF52810 with a PA chip, the model of the PA chip is RFX2401C. The attachment is the manual of the PA chip. The hardware connection...
Dear Nordic,
We use CONFIG_BT_CTLR_DATA_LENGTH_MAX definition set to 251 in our project to be able to send large data packets. Still, when migrating to nCS 1.6.1, we've...
