Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Dear all,
I'm trying to modify ble_central_uart (SDK16) to connect two peripherals. I've achieved the connection and been able to print receiving data via UART.
But...
Hi All,
I am NEW to Nordic Devices and I want to try to learn as much as I can.
I have bought a startup Dev Board to learn my skills with: E104-BT5032A-TB E104-BT5032A...
Hi guys.
I wonder the program run start from which section and how to enter the app when 52840 poweron? Start from SofeDevice?
I only flashed ble_app_uart and SoftDevice...
Hi all,
I'm trying to transfer my custom project pca10056 (which is to broadcast a beacon) to nRF52811 hardware and I'm facing some issues in the last stage of build.
...
HI ,
My environment:
nrf connect sdk
nrf5340 dk
segger studio ide.
could you please provide me timer example code for nrf5340 board.
Thanks & Regards,
...
Hi,
I am using an NRF 51422 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the...
SDK: 17.0.2
IDE: SES
nRF52832 module
Hi!
I have a nRF52832 based custom board operating on battery power. I assigned a variable to the non_init section in SES and...
Hey!
I have an isp1807 test board, which uses an nrf52840 chip, and an isp1p807 programmer (ISP130603E). Currently, my code is written using the nrf52 sdk v17. When I am...
Hi, I'm using nRF9160 as host and nRF52833 as a controller with NCS 1.5.0 SDK. On nRF52833 LPUART sample runs, I have added needed configurations for extended advertising...
Dear All,
I am working on interfacing BME680 with nRF52840-DK board. I got the output for Temperature, Pressure and Humidity but not getting the output for Gas resistance...
What should be considered for choosing a chipset? the followings are in my mind. Could you please tell me if I am correct and if I should consider anything else too.
1)...
Hi guys.
I flashed a uart-dfu Bootloader(SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_uart), when the program run...
Can you, please, point me towards documentation and (if available) samples of mobile app that would allow me to commission and then interact with devices in RF52840-based...
Hi everyone,
So currently, i am working on a project relating to sending some message from one router to another. I found out that there is a function to create your own...
