Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
I am entering the saadc source code based on ble_app_uart.
devzone.nordicsemi.com/.../i-am-creating-a-saadc-project-based-on-the-ble_app_uart-project
The source code...
I am advertising services, characteristics and descriptors. All are seen by nRF Connect (for iOS) but in the log I see this:
[Callback] peripheral(periphal, didDiscoverDescriptorsFor...
Hi,
We are currently evaluating a project, that uses the nrf52840 with an SD card and is connected as a USB device. One of the uses is the MCU is writing data to the SD...
Dear all:
When the PC1001 board connected with other BLE devices, how i can voluntarily disconnect them?
it seems that the use of the sd_ble_gap_disconnect function has...
I would like to use the latest version of Mbed TLS (2.26.0) on the Thingy:91 and then realize a TLS connection using this version. As a first step I integrated this particular...
Hi Nordic Team,
1. Actually we try to debug "Mesh Light" sample code using "Build and Debug" option of Segger Embedded Studio.. 2. Unfortunately debugging stopped at below...
hello,
i am using nrf52840 in our customised board and trying to interface it with GDEW0213Z16 2.13 inch display which uses spi communication i have added the necessary...
Hi.
I'm new on this form and also new on nrf dev board. I want to use OLED with nrf52832 using Twi / i2c. I grab some code on Github https://github.com/monpetit/nrf52-spi...
Hello , I am trying to develop my own application using ble mesh sdk in nrf52840 provided by nordic.I have gone through various examples and various blogs.
I want to know...
I'm using NCS v1.5 and nRF52840
I'm trying to achieve low power consumption.
I turn on scan using, which draws around 9.5 mA.
What I'm then trying to do is turn scanning...
Hi, I want to create bootloader for my code. For that I have install Python3 (Python 3.9.1)
followed by installing pip and nrfutil
python -m pip install --upgrade pip...
I use sd_ble_gap_device_name_set to set 10 chars device name
then getting NRF_ERROR_INVALID_LENGTH in sd_ble_gap_adv_set_configure.
all OK when tested 3 chars device name...
Good morning,
I am developing an application that needs to match a central with a specific peripheral. For this, the first time they connect, the address must be saved and...
Please allow me to introduce myself, I am product Engineer at Epson Electronics. I am supporting Nordic on Reference Designs.
I noticed in the new nRF5340 there are two...
Hi Nordic:
I think this should be a same old question, but as following thread mention:
https://devzone.nordicsemi.com/f/nordic-q-a/38292/mesh-proxy-sdk2-1-1-tx-power...
