Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
I was doing some current measurements and tried to reconnect my DK to my computer to put a new program on it. When I try to Connect J-Link, I get an error that says...
the link infocenter fail to download in:
(General PCB design guidelines for nRF52 series)
https://devzone.nordicsemi.com/nordic/short-range-guides/b/hardware-and-layout...
Hi,
Do you have a drawing of a recommended PCB layout footprint for the nRF9160?
I found a link somewhere, but the page didn't exist.
I need a drawing - not an Altium...
As i an trying to establish LTE connection using nRF9160.but i want to use external antenna because i will place nrf9160 module in metal enclosure. please suggest best antenna...
Hi pals!
I'm trying to do the throughput example with using 2 nrf52840DK. I downloaded SDK15.0.0 and I'm using ble_app_mtu_throughput example under ble_central_and_peripheral...
Hello there,
I've been following a guide Installing a 6LoWPAN enabled Linux kernel and required modules as a part of setting up a BLE 6LoWPAN border router on Raspberry...
I'm working on an NRF52832 product that will be intermittently powered, and the supply rail may fluctuate slowly, drifting above and below 1.8V.
I saw this post:
https...
Hello everyone
I am using nRF52840+wifi module to communication with the server via MQTT+LTS, Now MQTT communication with server was successful, Considering the safety,...
Hi everybody!
We have a problem with our product. It is based on nrf52832.
We used heart rate example in the SDK. MCU sleeps after a while if it is not connected. We have...
I'm trying to combine conventional pairing with OOB NFC pairing, but I'm struggling to decide which libraries to use. I have been looking at the examples, and they all use...
how can we properly set the scan timeouts? Say if we need to scan for a device for 5 seconds and if it is not available we can stop the scan and search for a new device. i...
Hello I am getting fatal error and system reset after calling APP_UART_FIFO_INIT.
I want to receive some data over ble and send it to the uart. I connected physical UART...
Hello, in my application I have a problem with the app_timer module respectively with a timer I have created. I'm working on a nrf52832 ( Rev. 1 - build code QFAA-B00) and...
I need a solution for doing a DFU from an Android phone to a device with a nRF52832 chip in it
I currently have a working version in IOS Swift but cannot get the Android...
Hi everyone,
I'm using nrf52840 custom board (pca10056)
SDK version: 15.3
OS: Fedora
I work on a custom board and try to use WDT like so in the WTD project example...
