dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello!
I am using NRF51822 in receiver mode with enabled interrupt on ADDRESS event, and even if transmitter is switched off I still get a few messages every second. It...
hi........
i have customized one program ....using segger 15.2 ...nrf52832
when degug it,the code from button and leds stops at nrf_breakpoint_cond ... even it doesn't...
When performing pre-qualifying Bluetooth radiotest of our hardware (utilizing the nRF52840-chip) at NEMCO, we experienced very strange behavior. The frequencies detected in...
My setup of the buttonless BLE DFU secure bootloader using SDK15.2 isn't launching the application after a successful OTA package transfer. Using RTT and breakpoints, I narrowed...
Hi ..
I am using nrf52832 and peripheral device sensor ..segger 15.0
Is it possible to wake up from sleep by interrupting the sensor .. possibility is there ??
Hi,
I am shifting my program from version 11 to 15.2. While including SPI files to the ble_app_uart code, I met with this issue. I have enabled all defines for SPI interfacing...
I'm trying to get the ble_app_uart example working on a nRF52810. I'm using SDK 15.2.0 together with Softdevice S112.
The infocenter says the Example needs Softdevice S132...
I'm facing the issue, that the app_ble_uart example just works if I hook up TX/RX of my USB - UART converter. Is this a desired behaviour? It doesn't seem to start and advertise...
Hello Nordic team
I am working on nRF52832 DK with SDkv15.2. Example code ble_app_buttonless_dfu.
I have created successfully bootloader and zip file to update the firmware...
Hi Sir/ Miss:
I use master emulator to develop software testing device that dll version is 2.1.13.14.
It's developed on using C#.
And, I use nrf51 dongle (PCA10031...
Hello,
I need your help, please review the following description and help to let me know the method to solve the issue,
thankful for your support in advance,
the...
We are going to FCC lab shortly to certify nRF51822 BTLE. We have done this before on previous products and passed with the same radio block. Unfortunately our compliance...
Hi. I'm currently using nrf8001 and i need to send data consecutively and as fast as possible.
Connection interval used: 20ms
Data payload: 20bytes
Service pipe used...
