Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
What is the best way to do migration between SDK 11 to SDK 15.
There are guides for each step. Is the best way to do SDK11-SDK12 then SDK12-SDK13... ?
Thank...
Hi,
I just switched over from the nrf52840PDK to the nrf52840DK and I'm running into an issue where the DK board is not firing the NRF_USBD->EVENTCAUSE = Ready event....
Hi,
I'd like to inquire about the recommended configuration for RF conducted emissions testing for the BTLE radio on the nRF52832. As in the reference circuit provided...
I am trying to send more than 255 Bytes of data over I2C so I break it up into 255 byte transfers within a transaction.
I notice a stop/start condition is sent between I2C...
Hi,
I am trying to have two instances of SPI with the same data and clock pins but to two different devices and thus two different select pins.
I have set all the SPI_Enable...
Hi,
The nRF Connect iOS and Android apps provides detailed instructions and functionality for enabling the device boot loader via the iOS/Android] mobile apps. When running...
Hi,
I have a application where the TWI is always reading a sensor in the main task.
When the DFU requiere to reset, frequently the TWI is busy and the current frame is...
I am using nRF5_SDK_15.0.0_a53641a with a nRF52 Development kit. The board is Rev 1.2.4 (the sticker on the bag says nRF6827 and the sticker on the chip says PCA10040). I...
I am struggling to configure all of the options I desire to on the the "ATT-MTU Throughput Example". This is the version provided in the v15.0 of the SDK, with the hex file...
Hi,
I have two nrf52dk devices.
I Want to test the BLE examples which can exchange Bytes of information between each other and display over the UART.
Which examples...
Hi.
My target board has a power switch that is managed by GPIO.
First-time, a user clicks the button, the GPIO is turned on and the system wakes up.
In reset case(Firmware...
I'm troubleshooting my NFCT state machine -- I'm getting a lot of FRAMEDELAYTIMEOUT errors and can't understand why, I'm triggering a TXSTART ASAP... but that's another issue...
Hi there,
Is it possible to feed XC1 or XC2 with an oscillator output rather than using a crystal?
It would make sense for me in terms of application but I cannot see...
hello , I followed this tutorial : devzone.nordicsemi.com/.../wireless-timer-synchronization-among-nrf5-devices
when i put the button 1 i have just a signal of 2 second...
Hello,
I want to use the D-/D+ as general I/O pins but noticed that it's not mentionned "General purpose I/O" in these pins.
Are these pins only available for USB ?...
