I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
I am developing AoA for nRF52833.
Please tell me about antenna switching.
Setting:
PSEL.DFEGPIO[0]=28 PSEL.DFEGPIO[1]=29 PSEL.DFEGPIO[2]=30 PSEL.DFEGPIO[3]=31
SWITCHPATTERN...
Hi folks.
recently I've been experimenting with the nrf7002dk Development Kit, and I'd like to move forward with prototyping a custom board around the nRF7002 + nRF5340...
The board is nrf52840 based using mcuboot via usb, mcuboot can be activated using a switch, and is indicated via a led, all setup via device-tree, so no legacy here. Software...
Hi,
I am trying to connect nrf9160 to CMW500 callbox however I am not able to connect to it. Switching to a commercial sim card I was able to connect to the network. I am...
We are finding an issue where after a network is running for a while we are unable to interact with devices beyond connecting to them via the nRF Mesh App. Specifically, we...
HI,
I found that nrf Desktop (v2.9.0 nrf54L15) surport fwupd support, it's same with old mcuboot DFU? and i want to upgrade from SPI, how can i do? is there any demo code...
I have a few questions about the sample source of nRF5340 Audio.
1. Where does the connection processing between the Gateway and Headset take place?
2. Where is the BLE...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-5-serial-peripheral-interface-spi/topic/exercise-1-10/
spi frequency is 1000000 in DTS...
My company is working on a project that uses the nRF53 that needs to wirelessly send out data roughly every 3ms (via ESB). We are now at the point where power needs to be...
In nrf5340 audio application( SDK2.9.0), I try to set phy to 1M in CIS( 1 gateway,2 headsets).
I made these changes：
Add in prj.conf:
In C:\ncs\v2.9.0\zephyr\include...
Hello,
I'm working up an application where tens of kilobytes are sent via bluetooth to a device which then stores the data on the internal flash (nrf52832). I've worked...
I want to change the Tx power in nrf5340 audio application.
I add CONFIG_BT_CTLR_TX_PWR_PLUS_4=y to prj.conf, but the power didnt change.
How to increase the power ...
I am developing a new custom board using thingy53 as a reference design. The way I programm my thingy53 now is to use the SWD debug interface with a nRF5340 DK. I understand...
Different boards with the same layout have different power consumption when using NRF54L15.
The circuit board layout myself is used for locator tag development.
broadcast...
