when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151 design and I have two questions about the QM13345 configuration.
1. LUT
The Thingy...
I have been testing the HTTP FOTA procedure as documented here using the 1.5.0 test diffs as provided in .
Many of the messages output by the modem in this upgrade process...
Hello,
We are seeing a west build reproducibility issue on nRF Connect SDK v3.4.0 that we have narrowed down, through extensive elimination, to the compiler's code generation...
**Setup**
- Custom board, **nRF54LM20A** , first bring-up. The SoC is powered from an
nPM1300: BUCK1 = 1.8 V feeds VDD.
- External **J-Link** (firmware compiled Jun...
Hello,
I have a tight loop with strict timing requirements that I'd like to run on the FLPR core of the nrf54lm20. In each iteration of the loop, i need to write data to...
Hi，
When we draw PCB, we also need to design it like your DK board? There are several square copper skins under the chip, the middle of which is grounded, and the other...
I have nrf52840 DK board, running cutom image that implements BLE central, constantly scanning on coded (S8) phy. Trying to add NFC T2T tag, and it doesn't work. Disabling...
Hi,
While characterising low-battery behaviour of the nPM1304 on the nPM1304 EK I see the following:
1. With VBAT above ~2.4 V, Ship mode current is ~0.40 µA, as expected...
In the bare metal SDK, for the cgms routine, if we switch to the internal LRC, how should we configure it?
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC =y
After making this configuration...
Hi! I know that FindHub is supported on nRF Connect SDK, but I'm wondering if there is any support for it on nRF5 SDK for the nRF52840? The use case would be adding the feature...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151-LACAA1A design, and I would like to make sure I understand the recommended correction for...
I am beginning to work on a next generation of environmental sensors. The current group of sensors use the i2c, or oneWire communications bus. The current standard micro-controller...
Hello Support Team,
I am currently working with the Matter contact sensor sample ( ncs\v3.4.0\nrf\samples\matter\contact_sensor ) on the nRF54L15 Development Kit (DK). ...
