Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi，
Due to customer demand, the 52810 chip must be used during development. At present, there are too few flash resources in the application layer, and the starting address...
Hello, For our project, we have a gateway which is in a mesh network with others devices. But we would like our gateway to be able to, sometime, connect to a specific device...
Hi, I have some questions regarding the nordic distance toolbox:
Can we use the distance measurement tool with 802.15.4?
if yes, how can the synchronisation be done...
We have queries regarding nPM1100 charging IC, I have mentioned our queries below, Please share your response.
1. What is the main purpose for the s hipping mode and purpose...
I transfer data by ESB between send and receive. And I want to transfer 2 bytes x 10 data that is received by ESB every T[s] to ESB receive (trigger) -> PPI->SPIM, 2 bytes...
I am trying to conduct a basic topology featuring two NRF52840 boards using the Thread Topology Monitor and a thread application using CLI. Once built and connected with J...
With the Bluetooth Low Energy v3.0.1 app within nRF Connect for Desktop, if I use either the nRF52833 or nRF52840 Dev Kit boards as the scanning device it is able to connect...
Hi,
We are using bl-653,
we wanted to enable UART-1, for bl-653 we wrote overlay & configurations mentioned below:
&uart1 { compatible = "nordic,nrf-uarte"; current...
Hi,
we are observing an interesting range of problems on nRF52840 devices we are assembling, where some percentage of them fail with the following error. While ti may be...
Hello, guys.
We are using nRF51822 SoC together with nRF5 v12.3.0 SDK.
According to the nRF51822 memory layout , half of the 256KB flash memory space is taken by the Softdevice...
Hi, I am developing a zigbee device on Nrf connect sdk 1.9.1 which has 9 endpoints, i am not able to create more than 8 endpoints perfectly.
i tried to change ZB_MAX_EP_NUMBER...
hai,
i am using nrf5340dk NCS (pca10095) v1.9.1 ( using visual studio code IDE )
i want to use nrf5340dk GPIO pins for NETWORK CORE use.
referred Nordic and zephyr website...
I added a new event module to asset_tracker application. The default LOG_DBG messages are very well shown in LTE, but that of my module don't appear in LTE. I replaced LOg_DBG...
I need help extending the LWM2M sample to use PSM to optimize the power consumption of LWM2M.
Scenario:
1. Enable PSM on the LWM2M sample.
2. Set the Lifetime of the...
Hi,
I got a product with nrf52832
i use one uart and i need to add another rs232 uart to it.
Since the NRF52832 has one only 1 harware uart i thought about implementing...
