Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi guys !
I am working on SDK 15.2 and I have created a custom service thanks to this tutorial : https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial
...
Hi The nrf9160 product spec 1.2 states that the number of times a 32 bit word can be written is 2. I have used the nrf52840 a lot and has a similar restriction but on seeking...
Hi,
In my project, there is a lockup issue like the title. (SDK 15.3.0_59ac345)
When I try to erase flash, some data (uart command for the device)comes up through the...
Hello,
The last ticket referencing this topic is 2 years old. I thought I would ask this question since we now have NCS.
Application is a Gateway that will support Zigbee...
I am trying to fun the LTE Sensor Gateway on the Thingy:91.
The boards are missing from zephyr so I copied nrf52840_pca20035 and nrf9160_pca20035 from ncs\nrf\boards\arm...
Dear all,
I'd first like to apologize if my questions seem dumb. I'm a student in mechanical engineering and only just started getting accustomed to microcontrollers and...
Hello,
I just installed SDK and Embedded studio.
And when I try to rebuild example, error occurs.
Below is my setup information.
- SDK: nRF5 SDK 16.0.0
- Example...
Hello support,
Currently i'm working with one application using NRF52832.
in which i have to fetch data from coming from PIC controller to NRF52832 over UART communication...
Hello, I owe a nRF9160 DK version 0.8.2. The ERRATA 0.7 document says that for this version the GPS antenna does not work well. I need to use GPS for extracting PPS signal...
Hi all, I've been recently working on PSM for my device, and I've not found any resources that answer my query or provide the knowledge I need. From my reading in this article...
Hello whenever I am calling sd_power_system_off(), it gives me the following error- implicit declaration of function 'sd_power_system_off'.
What shall be the optimum solution...
I use a 3.3V battery as VDD on an nRF52832 device.
Along the line this battery might do down from 3.3V to 1.8V. Will the Internal Reference Voltage be consistent at 1.8V...
Hi,
In apply_old_config.h ,here is the code:
for example:
If I set SYSTICK_ENABLED =0 in sdk_config,here will overwrite the macro define because #if defined(SYSTICK_ENABLED...
As per the datasheet of nrf52840 any peripheral like SPI/UART/... can be configured to any of the GPIOs so is the QSPI also.
But at Pin details QSPI pins are recommended...
Hello,
We are working on machine health monitoring system. For that we are using nRF52840 SOC as Central and nRF52833 SOC as end node. We had used single Central node and...
