hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
I'm new with Nordic products, I bougth one nRF52840 and I tried to install Segger, to start programming.
I had a problem when I tried to open a SDK on Segger. When I try...
I'm using a custom nrf51822 board with S110 softdevice, and SDK 10. This board is used as SPI slave with BLE. I tried to estimate the stat up power consumption by reading...
Hi, we are developing a bluetooth device in my company that must transmit at a distance of about one kilometer. I saw that this soc has been tested up to 1300 meters. It's...
1. By the toolchain manager, the sdk connect and zipped toolchain were downloaded.
I used the downloaded SES to compile examples. For others, they can compile successfully...
Hi All,
My one of the old application is based on SDK11 and i found some issue data corruption with FDS module. After reading some post here regarding FDS issues and also...
Hello,
I am trying to evaluate the Channel Selection Algorithms (CSA) 1 and 2. From what I found on here, CSA 2 is enabled by default in SoftDevice stack, could you please...
Hello everyone. I want to create project from stracth for nRF52832. I use nRF52 DK. I couldn't find any tutorial for this. I create new project under nRF5 SDK 16.0 and specified...
I am using BT840F module from Fanstel which is based on nRF52840.
Currently I am having two EV-BT840 (Evaluation kit for BT840). I have modified 'pca10056.h' as per my board...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello Devzone,
I've been working on a system to set notifications on time ready for transmission.
The client sends a WWR package to my peripheral and I want my peripheral...
Hello,
Currently, I'm trying to flash my custom board that has nRF52832 with an uart application that I integrated buttonless DFU. I'm running into a problem where when...
1.nrf9160 is there an RF calibration parameter at the factory?
2. If there are calibration parameters, does burning mfw_nrf9160_1.2.0.zip firmware affect the calibration...
I have two devices here, So I combined three HEX files and burned them with JLink, and they don't behave the same. One starts the application normally, and one is always in...
I am using a custom board with nRF8001, where I use external interrupt from the RDYN pin to let MCU know BLE has an event. MCU can recognize these events and change the associated...
