Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Hello, We are using a nrf7002 for wifi only alongside a nrf5340 host MCU on a custom board. We are testing the wifi connection using the sample `nrf/samples/wifi/shell`, with...
Hello,
I'm trying to enable RTC2 for nrf52840 DK to use as a date time clock and set/get over SMP protocol. RTC0 is used for MPSL, RTC1 is used by the system.
I configured...
Hello,
We struggle to keep LTE-M attached with nRF91 (Modem) and CMW500 (EPS) to test regular IP communication (so those are not Radio Access Network tests) during product...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
Hello, I have 2 PCBs for drone communication using nRF52820 and nRF21540 FEM module. I'm using the ESB protocol to communicate via radio. There are ready-made esb_prx and...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Hello everybody,
now, I am solving problem with switching off Wi-Fi interface on nrf7002-DK. I am runnig SoftAP example on my nrf7002-DK board. So my board behaves like...
Hello guys!
I have a strange problem where the nrf9151dk suddenly won't power up. It was working fine - I was only working with SW, not HW.
I got a pop-up error saying...
I'm developing my application with nrf52832 and nrf SDK v17.
I'm testing my program.
After running for some time, Jlink output the following.
When the "Logs dropped...
Hi,
I noticed in the nRF54L QFN48 reference design, for the NRESET pin, there is an RC filter (1Kohm series R and 3.9pF shunt cap). What's this for and is it necessary?...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but it flash but can't run RF...
hi，all
Chip: nrf52840
SDK: NCS 2.9.0
We are currently developing an integrated factory testing function using mcuBoot's DFU. We want to make slot 0 the default for factory...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
