Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
After a successful LESC bonding, the address given by p_ble_evt->evt.gap_evt.params.connected.peer_addr in a BLE_GAP_EVT_CONNECTED event is a "identity address" as expected...
Hi,
I've been trying to figure out how to configure a nRF52832 device using SDK 15.2 and S132 to act as both a central and peripheral device for a relay device. In looking...
Hi,
We have a custom device that has 15 buttons. Presently we use the following code to initialize and use the button interrupts. I am using a __WFE(); to wait for the next...
I got this project to compile and work: https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master/samples/nrf9160/gps
I have the latest radio firmware at this time...
Hi Sir or Madam
nRF52832 support ANT+ function using 2.4G ISM frequency, but i am not sure the frequency list and channels number/ frequency bandwidth, is there any software...
Hi,
i am trying to interface ultrasonic sensor with nrf9160, but i dont get any examples regarding ultrasonic. so i tried the interrupt method to measure the time of gpio...
nRF52832 Product Specification v1.4 states:
11.3 Writing to user information configuration registers (UICR)
User information configuration registers (UICR...
Hello Nordic team,
I'm currently looking into TLS on nRF52840, I'm using nRF SDK 15.3.0.
I have seend the DTLS example "nRF5v15.3.0\examples\iot\dtls\coap_client" that...
Hello Nordic experts,
I am doing SDK 15.3.0 usbd_hid_composite example and this is where I am: https://devzone.nordicsemi.com/f/nordic-q-a/50447/nrf52840-usbd_hid_composite...
My firmware goes into system off state when idle and wakes on GPIO (button input). I want to display an indication to the user for a fixed duration, so I will modify the bootloader...
Hi,
I'm using nRF51822 chip and SDK 12.3.0 library to develop the software. We want to control the motors with PWM. But since PWM consumes a lot of power, we decided to...
Hello.
For My personal project , i would like to develop a buttonless OTA DFU on my Red Bear Nano V2 (Based on nRF52832 SoC Chip) . Im using the SDK11 and i have folloawed...
I'm trying to add RTT support into the secure BLE bootloader to get debug logs, but after adding the files it's consuming too much flash:
Is there any way to fit RTT support...
