Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello i am working with light switch proxy client server sdk example.i make provision light and switch using nrf mesh application.i have three nrf52832 dk board.i flashed...
Hi.
I work with PCA10040 and SKD_14.2.
I use UARTE with easy DMA. I see big enough delay between sending nrf_drv_uart_rx_abort and entering to UART event hanler. What...
I tried to create a descriptor for a characteristic. I modified the app_blinky and added a ble_add_descr_params_t variable. After The Initialisation and definition of the...
Hi,
I've tried blink,hid,uart,template similar sdk examples so far. Now i acquired some experience about nrf52832 processor and bluetooth,but ii don't really have enough...
I have had an issue recently with some beacons that I am using to log temperature data. A portion of the beacons drained their batteries very quickly and didn't respond to...
Hi I have this piece of code which works in SDK 12 but when I port it to SDK 15 the sd_ble_gatts_characteristic_add function would fail with an error code of 7. No change...
Hi,
I want to put my nrf52832 into the low-power mode. I select SYSTEM ON with low-power (instead of SYSTEM OFF) in order to overcome reset. In order to do it I call sd_app_evt_wait...
Dear nordic team
I am using SEGGER EMBEDDED STUDIO and nrf52840 DK. I want to add some pwm nrf_drivers like nrf_nvic.c , nrf_soc.c , nrfx_pwm.c to my project. when i added...
Hello,
I started off with two nRF52832 Dev Kits, and have customized the UART Central - Peripheral example to send an array data from Peripheral to Central (no uart simulation...
A month ago I bought an nRF52840 DK to start creating my own projects with the nRF52840 chip
I have created a new project in Segger Embedded Studio for the nRF52840 DK....
Hi,
is it possible to use the nRF52 dev kit and/or the nRF52 Dongle (nRF52840 Dongle) wiith the dongle firmware without nRFConnect?
Background:
We want to use a nRF52...
AIM: Try ATT MTU Throughput Example on nRF52810 running on S132 v5.1.0
Reason: Cant use S112 on nRF52810 because of data length extension. Max speed achievable is 330 Kbps...
Hi,
I have nRF52832 connected to a device(A) which can operate from 3.3V to 5V supply.
When the device's supply is 3.3V, it communicates with nRF52832.
Before the device...
Hi ,
If the softdevice had inited (called sd_ble_enable() ) , Can I use the NVIC_EnableIRQ (or NVIC_DisableIRQ )
to enable/disable an interrupt ?
What is the difference...
