Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Dear Nordic Support Team,
I am working with the nRF52840 in a multi-protocol setup and would like to clarify the feasibility of the following configuration:
Running Thread...
Hey,
we're currently testing our devices with Modem FW 1.3.4 / nRF Connect SDK 2.2.0 and have observed the following error:
LTE-M
Connection was successful before...
Hello Team,
I am using nrf54l15 dk for the development. In this, I am using k_sleep to put the device in system-on sleep mode. Using this, I have achieved the sleep current...
Hi,
I need to use AES CBC 256 encryption/decryption on nrf52840 but since its cyrpto cell only supports AES 128, I tried using mbedtls to do AES 256 encryption. It works...
Hi,
I’m working on loading batch data from a BLE server using SDK version 2.8.0 with the nRF9161-DK hardware, and I’ve encountered a couple of issues.
Different Results...
Hello,
the mass production firmware of our product was generated on NCS 2.2.0 (MATTER 1.1). Now, we are attempting to OTA upgrade our product to the firmware based on NCS...
When dealing with low power access via NTN (via Skylo), is there any limitation about any particular use of SW?
Like, is Zephyr or other RTOS combinable with the Skylo certified...
I'm trying to flash a XIAO nrf52840 following the instructions for flashing with UF2 but it won't seem to work. After I drag and drop the zephyr.uf2 file in the mounted drive...
Hello. I am trying to implement stable connection between my nordic nrf5340 and Samsung Galaxy Buds3 earbuds. I did it based on ble audio example with two connections (one...
I have a 7002dk dev kit. Currently for evaluating the nrf5340, which will be used in my product. Currently i am trying to evaluate if it is possible to use the nRF5340 USB...
Hi,
I am using two nRF52833 DK and both are connected with nRF21540.I notice that when I have a very high throughput, never stop sending 244 bytes, I will notice that average...
Hello, I connected my (working) PPK2 and opened the PowerProfiler. Immediately, a "DFU needed" message popped up.
I DFUed the PPK2, and in the logs, it wrote DFU successfully...
Hi,
I would like to ask about the future plans for Zigbee development, as the current situation is a bit confusing.
From what I’ve observed, Zigbee R22 has been deprecated...
My team recently acquired two NRF24 transceivers to use on our drone project. Personally I've used NRF24 modules before and have successfully paired them with Arduino and...
Hi all,
i just received 2 nRF54L15-DK boards. Both I am not able do program - I tried:
1. nRF Connect for Desktop
* I did not make any change on the board afre unpacking...
