Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Is it compulsory to have same Baudrate on central & Preipheral side when using the NUS..?
I'm using Central @ 115200 & Peripheral @ 9600 [No flow control on either].
...
Hi,
I've written an app on the nrf51822 (rev2), with S110 (v7.3.0) and SDK v6.1.0. I've written a custom non-blocking UART driver. I'm running into an issue where the UART...
Hi,
Using the nRF5 11.0.0 release SDK, I'm trying to set up one task to transmit to and one task to receive data from the UART. Nothing special.
The configuration block...
Hi,
The xQueueReceive function in FreeRTOS seems to be broken, when a non-zero timeout is specified.
Example, I'm trying to create and ordered output mechanism for the...
Hello there,
I managed successfuly to build the 'ble_app_hrs' of SDK10 on my NRF51 on GCC MARS 2.0 using these two guides combined:
devzone.nordicsemi.com/.../
devzone...
When i use the nrf_drv_adc with NRF_ADC_DEFAULT_CONFIG i get the following compile errors:
rf_drv_adc.h:127:27: error: 'ADC_CONFIG_IRQ_PRIORITY' undeclared here (not in...
I am developing a real-time system which triggers an interrupt every few milliseconds. That data is collected in the interrupt. When a memory buffer is full, the data is then...
Hi,
i am trying to start a RTC0 on nrf52 DK with SoftDevice (s132) enabled with project based on "ble_app_template". The problem is that a sd_softdevice_enable() (called...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have setup a development environment using Eclipse and GCC. This setup works nicely. Thanks!
devzone.nordicsemi.com/.../
I noticed different examples in...
Hello,
We are currently designing the hardware for a production run of our product using the nrf52832 chip and would still like to have debugging capabilities with breakpoints...
I have been learning GCC+ Make work flow to build and debug nRF51822 S110-only applications based on the examples from NRF51 SDK v10.0.0. I started with ble_app_beacon example...
I tried to work application.
But firmware stops at advertising_init(). When I exchange advertising_init() and services_init(), firmware does not stop.
why ?
S110 v8.0...
Hello,
My device is nRF51822 SD110 8.0.0.
The problem occured after firmware update in bootloader (own, not SDK) with readback protection enabled.
So bootloader connects...
Hello,
I am currently finishing my deploy script and I am currently using nrfjprog to write some custom UICR data. I have a contiguous region of memory to write but I do...
