I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hi
I am writing my own bonding manager.
In the S110 stack after Phase 3 of pairing the keys are exchanged which result in the EVT_AUTH_STATUS event which in turn contains...
when I add my own service and add characteristic, a odd phenomenon confuse me.
When I set cccd_md.write_perm:
BLE_GAP_CONN_SEC_MODE_SET_OPEN(&cccd_md.write_perm);
...
after several attempts to debug and understand what goes in my handlers in the BLE callbacks, I thought to give a UART logger a try.
this is what I'm trying to use: OpenLog...
Hello,
I am looking for a not expensive way to program nRF51822 by frame of 10 modules. All the 10 modules would be connected to a PC using pogo pins, and I would use a...
I can get an information that bluetooth smart connects bluetooth smart ready.
But I can't get an information that bluetooth smart connect bluetooth smart ready.
So, Would...
I am using nrf51822 and i want to run my application using softdevice.
But I am not able to start my softdevice Please can anyone guide me how to start my softdevice.
I...
How to enable the notifications or indications? In APP? can I enable it in ble peripheral?
I meet a chip of "Quintic" can do this. When I connect it to MCP and I get this...
I made Pwm program with 3 channels without using softdevice and without using interrupts at that time it is working perfectly. But when i am trying to use softdevice with...
Sometimes I receive pipe error 0x92 when I try to send a message from nordic to Android. What could be the causes for a pipe error 0x92?
I saw this: "Pipe Error Event ...
Hi,
I purchased nRF24Lu+ modules on ebay. I am trying to talk to them over USB from a linux machine.
Nordic datasheet states:
VID = 0x1915 and
PID = 0x0101
When...
Am I right in thinking that these security parameters are contradictory in that for the peripheral (nRF51822) to provide MITM protection, there must be either IO capabilities...
I just received my nrf51822 and am using an-36 as a starting point to build my first "Hello World" application for BLE.
All I would like to test is to have the status of...
I am trying to only perform calculations for connected ble services.
I am implementing a state machine that monitors the ble evt.
I use this for example when to perform...
