Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Hi,
I work on a BC805M module (nrF52805) with the sdk17.1.0 & S112. It is powered by a CR2450 battery.
I like to reduce the consumption of the ble_app_beacon exemple....
Hello,
I am using the nrf7002 ek and attempting to optimise the RAM assignment for the project. I have reduced the size of several thread stack sizes as well as the heap...
Hello,
I wanted to reach out about the issue I've been running into regarding the UART Async API. I am having trouble narrowing down what the cause could be.
I am using...
Hello,
I have BLE TX Mask failed to the spec. as shown in the attached image. It seems noise floor is high. TX outpower at +4dBm (see attached CLI). Please advise.
Thanks...
So, hello, hopefully I have done my diligence to be able to afford some help, thank you!
Context: driving an ADIN1110 by Analog Devices with an nRF52840 usb dongle. Within...
I am trying to install SDK 2.1.0 on a new computer. I installed nRF connect extension in VS code, installed toolchain 2.1.0, and then when I attempt to install SDK 2.1.0 I...
Hi,
I've been using dev kits like nRF9161-DK and when plugging them in to my laptop they all work with the Programmer Tool, "nRFUtil device list", and the nRF Connect Code...
To explain our problem: We have a system with a NRF52840 chip, we also have an external flash, the settings_subsystem is mounted in the NVS on the internal flash I have included...
Description:
I am working with an nRF52840 custom board. I have encountered an issue where the board is not detected by the J-Link debugger after flashing the firmware a...
Hi all,
In Sidewalk, the Lora we are using is connected to DIO3 through TCXO, which does not match the XTAL of sx1262 recommended by the official sid_end_device demo. Do...
I successfully read accelerometer data at 3000 samples per second . However, when transmitting the data over Bluetooth Low Energy (BLE) , I am only able to send 200 samples...
Is there any pre-existing library similar to the Arduino avdweb_VirtualDelay library available for the Nordic Semiconductor nRF52840 Dongle? I do see the procedure on how...
Hello In SDK 2.6.xx I used to define an extra CMake argument in the VSCode UI, i.e "-DMFG=1" This argument was available when CMakeLists.txt was processed so I could do additional...
We have difficulties to get RTT prints from MCUBoot while performing DFU.
As far as I understand Segger RTT is reinitialized when booting Application and this might be the...
I want to change the bitrate for different settings：
Different settings with 48khz&10ms:
I try ot change the prj.conf to add these:
But an error occurred during...
