Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Hello, the chip I use is nrf52810 QCAA, when I use j-flash lite to earse the whole chip, it success, then I program the flash_s112_nrf52_7.2.0_softdevice into the chip by...
I am trying to merge the following projects:
SDK versions: 17.0.2 and 5.0
I have taken the contents of the mesh example sensor/server and merged it into the ble_blinky_example...
I created .c file, and add a few TWI functions to it. However, when I run the code in segger, all functions in the .c file shows a "multiple definitions of xxxx" error (see...
Hi!
I am working on an AoA project and I am using nRF Connect SDK. For the transmitter part I saw that sample application is already written and for receiving part it is...
Hi,
Our entire board is running around a nRF52832. Recently it has been difficult to find some of these SOC. Is it safe to replace it with the nRF52811 without changing...
Hi,
I am trying to compile ble_advertising.c file for a specific application based on nrf52840 and I am getting the following error:
nRF5_SDK_15.3.0_59ac345/components...
I am working with an nRF52840 on a custom board. Our device has a number of sensor attached in various ways including spim, twim, uart. I've used the ble_app_blinky as a starting...
Hi Dev Team,
I am enhancing my Thingy91 application using the mqtt_simple sample and NCS v1.5.0. I am basically connecting to the MQTT broker, sending data and then disconnecting...
I am using nrf52840 as PTX and nrf24l01+ as PRX. The application I am working on requires me to send 30 bytes from PTX to PRX at a 2 kHz packet rate. If both devices are near...
I am trying to make ble communication work with I2C but i cant make it work i dont understand what is the issue the code is being build but it does not advertise can someone...
I'm building a firmware for nRF52 which is using app timer v2 with RTC1. After a while, app_timer starts running many times faster than normal, and I'm not sure why. Nothing...
I use pc-ble-driver to control nRF52840 dongle. I want to speed up scanning of advertising time.
So I change SCAN_INTERVAL and SCAN_WINDOW.
How can I modify the parameters...
The enocean_switch example has MESH-config example, to store data in FLASH, within the mesh rules.
I use it in my app, IT WORKS, but the biggest data array what I can store...
hello folk,
I am working on nrf52840, I want it to assign Static UID of any kind that even won't change after the device gets reset.
I have already gone through "FICR...
