Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Hi guys,
I am using the RFduino nrf51822 chip. I am using the TIMER2 interrupt and it works fine. But when I try to use the BLE along with the timer interrupt both don...
Hi,
I have have one ble project which is using softdevice s110. so that i want to extend this project by adding DFU service to it like shown here
devzone.nordicsemi.com...
hi,
i have PCA10028 dk board. i want to flash code in this board using dfu. i have generated Zip file(both soft device and application(example ble_app_hrs example)) using...
I am using this DFU library github.com/.../IOS-DFU-Library . On iOS 10 while processing DFU I receive error RemoteInvalidState in didErrorOccur method with description "Device...
I want to know the maximum range for major and minor in Ibeacon frame, as it is of 2 byte can we set any values from 0 to 65535 or is there any limitation.
Hi everyone!
I'm using the nrf_soc API for get random numbers from the rng and erase and write the flash memory.
In my code, I include the nrf_soc.h file, in the header...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
Hello,
I tried to do DFU using MCP 3.10.0.14 and I'm getting the error:
"Error during firmware upload. Timeout while waiting for response for START DFU"
How do I increase...
I have secure dfu working on the pca 10040, and being able to download my own signed app.
However I want to turn NRF_LOG and at link time I get several messages of "._build...
Hi,
my application consists of long waiting time without connection (hours, possibly days, weeks), then a central connects and downloads data, and then again long waiting...
Hello all!
Sorry for what might seems an obvious question, my skills are what they are :-).
We have a small circuit based on nrf51822 chip.
Our software is currently...
Hello, I am new to embedded world.
I wanna know that how do i create a new template/blank for programming in uKeil?
Right now, i directly open an example from the SDK...
Hi there,
I am currently working on a project where I would need to use the Segger J-link needle programmer with 6 pin header. We have produced the board and after following...
Due to the PWM driver having intermittent issues we had to replace it with a TIMER/PPI/GPIOTE setup.
The PWM is working great in this way, but now I'd like to have one of...
Hi All,
i am using Stpm32 energy meter board.
i have gone through the data sheet completely.
i want to read and write the register values
i am trying to write 0xABCD...
