I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hello Nordic Support Team,
I am currently working with Bluetooth LE Audio using the nRF Connect SDK and Nordic hardware (e.g., nRF5340 platform). I would like to better...
Hardware :
n RF5340 on F ans tel B T4 0F module
Custom board , not a D K
High voltage mode : V DDH supply 5V , VRE GH V OUT set to 3.3V
DC /DC mode ...
Good day, everyone!
So I've been trying to implement a USB HID device in my development board for a few weeks now with the aid of some chat bots but it's gotten to a point...
In the cs_de.c, we have an IQ pair extracted from remote_pct and local_pct. Assuming this code runs on initiator (where the ranging is done), and remote/local stands for reflector...
I tried to use NRF_SOCK_RAW and NRF_IPPROTO_RAW to create socket, but found `modem fault`!
//this is my wrapper
socket_create ( true , AF_INET , SOCK_RAW , IPPROTO_RAW...
Hi, I very much doubt this is a SoftDevice issue but sticking it out there as an Apple dev asked me. Short story is I have users in production using an App connecting to NRF52810...
Hello Nordic Team,
I am using nRF5340 DK as a debugger/programmer to develop firmware for the Fanstel EV-WT02C40C module. My goal is to do i2c communication between Renesas...
Good morning, I have built and flashed the l2-e1 exercise on both the nRF5340DK and the nRF54L15DK. When the nRF54L15DK boots, the following output is displayed in the terminal...
Hi,
I’m working on nRF54LM20A and trying to configure the internal capacitors for the 32.768 kHz crystal (LFXO) using the factory trim values in FICR.
According to the...
Hello, read through the documentation about the SAADC and found the TRIM.LINCALCOEFF[n] register. ADC-linearity is important in the project I'm involved in... Seems that the...
Using nrf connect SDK 2.5.0
The nrf device is an L2CAP CoC server. I am using an RPi 4 to test with. The application is for transferring data through UART to another chip...
Greetings!
We have been using an nRF52840 Development Kit for a while now and have been performing FW updates OTA (between the same 3 FW images, cycling and updating between...
I am still on the learning curve of nRF Cloud (and the nRF9151 in general) and am trying to add A-GPS to a project.
Using nRF Connect SDK and Toolchain 3.1.1, I cannot add...
