i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi,
I'm evaluating the nrf54l15dk and am trying to make a small application where nrf54 appears as a tag. Upon initialization the `nfc_t2t_setup` returns -1 which does not...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
What this ticket reports
We ship a battery-powered nRF5340 product using the nRF Connect SDK's documented production security configuration: immutable bootloader (NSIB/b0...
Hello,
I have been a Nordic DevZone member for several years, but I have never published a blog post.
I would now like to contribute a technical article about an open...
Hi,
I've been developing the next version of our product with an nRF54L15 There's external SPI flash attached on QSPI via SQSPI which is working ok (albeit it is very slow...
Hello,
I am trying to understand how the documented tRXCHAIN value relates to the timing of EVENTS_ADDRESS in BLE 1M mode.
In this DevZone ticket:
https://devzone.nordicsemi...
Hi DevZone! I'm migrating an app running on a Thingy91 from SDK 2.5.0 to 3.4.0. I will eventually try to adapt it to the newest Thingy91X. So far I managed to migrate the...
Hi all,
We're building a PoC of a simple BLE device with a following setup:
custom PCB with nrf54l15 rev2 and 32MHz oscillator
FreeRTOS + custom port
nrfx version...
We are observing an unexpected increase in current consumption when enabling the LED driver outputs of the nPM1304.
We configure the LED drivers to Host mode , which by...
Hello Nordic support,
We are preparing a build-only NCS2.9.0 environment on an Apple Silicon Mac, macOS26.5.1 (25F80), with commands run in a managed workspace execution...
Hi, i have downloaded the app nRF for desktop, but when i try to download an app inside it (such as Programmer or Direct Connect) i get notified with this error
i try...
Hi Nordic team,
I am following up on a previous thread ( nRF54L15 sQSPI support for SPI NAND in NCS v3.3.1 ) where it was confirmed that NAND flash was not supported in...
The nRF91 series of modem firmware are distributed with FOTA-TEST diffs to allow for validation of FOTA integrations. Will the nRF93M1 firmware images be distributed with...
NCS SDK 3.4.0 NRF54LM20DK
The nRF54LM20A data sheet warns against using the same RAM subordinate by more than one bus manager. From section 4.2.1,
Avoid situations where...
