If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am trying to change TX power of advertising but even though I have written the below...
Hi
We wan't use in our project some MODBUS sensors and I found, that Nordic Connect SDK (I use version 1.9.1) with Zephyr has support for MODBUS. I tried the samples (rtu...
Hi to All Colleagues:
New to Nordic and its development platform. Finished installing required tools using nRF Connect for Desktop v3.10.0. Attempting to use nRF Connect...
Hi,
I'm investigating possible improvements to our custom firmware update architecture. I'm curious as to whether it is possible to run the SoftDevice from a location in...
I've just received nRF52840, it powers up and blinks as programmed and the buttons work. I hear the "ba bing" on my PC when it connects and disconnects, but the JTAG does...
Hi DevZone,
I need to change some defines in the ffconf.h file used by nRF5 SDK to set configurations for FatFS to enable use of f_findnext(), f_findfirst(), etc.
Is it...
Hi,
I have provisioned some nodes using interactive_pyaci successfully. Functionality is as expected. As a test, I then shut interactive_pyaci down, rebooted the nRF module...
Our Gateway uses a NRF52 and the sensors a NRF51.
Gateway is outside the freezer at + 20C and the sensor is inside the freezer at -30C.
What we see is the pairing becomes...
I'm working on a wireless musical instrument which requires a super low latency RF link. I previously was using NRF52810 and found that the latency was too high. The complexity...
Hello,
I'm a beginner ... I would like to connect a LoRa module (REYAX RYLR896) to send data from my nRF52840 Express to an Arduino UNO (with LoRa).
I don't know how...
Hello,
I am trying to work with the DFU examples provided with the SDK. My board is a custom USB dongle to which I need to add the bootloader. Following the steps from...
Is there a way to enable LE privacy for nRF52 DK in Bluetooth Low Energy App of nRF Connect for Desktop? I would like nRF52 DK to use resolvable private address when connecting...
hi, Im trying to read from a sensor register using TWIM peripheral on nrf52840 in blocking mode, but it wont work , doesnt freeze or anything .. just doesnt work
below you...
Hello,
I am trying to set system on mode in nrf52840 usb dongle.
This mode switched automatically by idle task, when there is no thread running.
There is no while(1...
Hello,
I m new to nordic in VS code. Bought two nRF5340 DK for ADC conversion and wireles data transfer.
Followed all Youtube install instructions "nRF Connect for VS...
