Does anybody got an app inventor2 "project" to communicate with the (Adafruit) Bluefruit LE UART (or SPI) ?
Note: my Android version is 4.4.2 (LE "advertising" not supported...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi, I have enabled DFU in my custom ble_hid_keyboard in NCS v1.6.1
when i copy the same project and placed in another name after that build successful but while running...
Hi,
I have merged these two codes from SDK:
\nRF5_SDK_17.0.2_d674dde\examples\peripheral\timer
\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_beacon
I want...
Hi,
I have nRF52 dev boards (nRF52840) (PCA10056), I am using SoftDevice nRF5_SDK_17.0.2_d674dde.
I am not sure SoftDevice SDK 17.0.2 supports BLE 5.0 specification: ...
Hi I am using Ncs version 1.6.0 and nrf52840dk ..BT_HCI_LE_SCAN_FILTER_DUP_ENABLE this duplicate filter enable is not working in NCS.is there any workaround for that?
I have a question regarding the power sequence mentioned in the nRF52833-Dk guide:
or the power sources section the guide explains it as:
I drew the...
Hi,
I know that this question was asked before, but I can't find a complete/recent answer.
We are trying to use nrf52 DK board to perform bluetooth localization. In...
I have a few questions about the bootloader of the nRF52.
I used "nrfjprog --eraseall" to erase the chip, afterwards I turned the power off and on again while holding down...
Dear Community,
I implemented the beacon-example with S112 and 1MBit mode and with S140 and coded-phy 125k sending one beacon per second continuously at +0dBm (sd_ble_gap_tx_power_set...
I have attached a sensor board to the nRF5340DK board I'm using zephyr 1.6.0 on macOS
I ran an I2C scan example using I2C1 peripheral and it works fine
found 5 I2C slave...
Hello, I have an issue. When I disconnect device I need to know it's mac address. Can you answer, how do i can get mac address of disconnected device or list of mac addresses...
Hi everyone,
I'm working with the BMD-350 Evaluation Board based on the nRF52832 BLE SoC and currently using a customized version of the central ble_app_uart example from...
We have an existing product that uses a module containing NRF52832-CIAA
Due to supply issues we are looking to respin our board to use a different module that contains NRF52832...
When I reset the device and in some time connect it to JLinkRTTViewer, it shows only 11-12 first messages after the reset. Which parameter I should change to increase number...
Hi, I tried to create standalone project based on SAADC example from nRF SDK. I copied all neccesary .h files etc., changed the include directiories. But then appeared some...
I want to try NRF52811 EYSNCNZWW with Jtrace but i am not getting how to implement this.
I have Cortex-m Reference board which uses STM32F407 micro controller, it has dedicated...
