If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
In one of my projects, UART interface is used for the communication of external sensors. During the power consumption test, I found that when 9160 enters the idle state, its...
Hello,
I am having nRF 52840 SDK for which I am able to control leds of sdk using ble app blinky example through android mobile.
Mean while, in nRF mesh provisioner example...
I'm having a bit trouble here getting migrated to LPUART on a working nRF9160 <> HCI BLE on nRF52 (On the Thingy91). As far as I can tell my .conf and .overlay files are what...
Hello,
I've run into a problem, which seems at least to be similar to that described in another thread . In short, if I set up a counter with CC[n] and start it, a COMPARE...
Hi,
I would like to store important information (few MAC addresses) in flash memory at manufacturing stage. Then my program will be able to read these information thanks...
Hi ,
My environment:
nrf5340 DK board
nrf connect SDK v1.5.0
segger Studio IDE
I would like to establish communication from application core to network core...
Hello I want to make a python script that allows sniffing of 802.15.4 packets (nRF52840), The module exposes an API that allows starting and stopping the capture. I installed...
I am using windows 10, nrfConnect 5340, and the NRF5340DK.
I was searching for an example of how to configure and use the usart/uart 0 port as a 2 way interupt based serial...
Similar to this problem , I cannot open the serial let modem example for nrf9160dk_ns. I tried moving my nrf install to the root but did not help. I am using Windows 10. The...
I want to read the acceleration sensor value using the example of the ble-hid-keyboard, but if I let you read the acceleration sensor value, Bluetooth will be cut off. Can...
Hello, I am having trouble understanding the flashing process of an nrf52840. I have programmed a simple flashing example with the nRF5 SDK. I compiled the project using make...
Hi Nordic,
I am using the two nrf52840 units to test adv and scanning in a pair for the development. I am using BLE_GAP_PHY_CODED for both scan and advertisement. But...
Hi,
We have recently switched from using nrf52810 to nrf52840. Firmware porting went well until we tried using the BLE on nrf52840. No matter what we try the BLE will not...
Hi, dear Nordic
1) Could nRF52810 Serial Debug Pin be used as GPIO/I2C?
2) Some post mentions using the external circuit, so that the 2 Serial Wire Debug pins can be used...
Hello
We have developped a product with the nRF52832. Due to space restrictions we couldn't use the PCB antenna design from the nRF 52DK. We used an Johanson chip antenna...
