Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
I am working on the MG996R servo and MG90S with nRF52840.
I am using the following delay logic to operate MG90S. (As per datasheet)
MG90S is working perfectly fine...
Hi ,
Just one question.
I am trying to create services using hrs examples and its useful.
Currently one question I have that ,
the battery indicator is only notifiable...
Using: Windows 10, nRF Connect v3.5.0, nrf v1.3.0, zephyr v2.3.0
I have a board based on the Thingy91 and the Asset Tracker application. I verified serial console output...
I want to quickly send up to 100KB of data to a connected smartphone and then disconnect to save battery.
I have most of this working using the NUS service but today I noticed...
Hi Team,
I would like to perform the DFU without using the nrfutil and OTA update. Is there any way to perform DFU without the nrfutil.
Our requirement is - We have...
Hello,
i built a SPI Master example based on this: SPI Master example
The example is a bit outdated and needed some rework and fix to work. I don't know if i am missing...
Hi.
NRF52832 is used as central for connecting with phones as peripheral. NUS service is used. Lesc is used too.
SDK 17 SoftDevice S132 V7.0.1
I have sometimes crash...
Hello,
From some time now i have been tryng to start developing an app, but i encountered a problem where the board does not connect, or does not find a provider from the...
Hi,
My goal: F lash hci_usb in my nRF52840 Dongle, so that i can use Bluez stack in my Linux host and nRF dongle as BT controller.
Build status: Success
Flash : Failed...
Hello,
I am trying to find the electrical and timing specs of the nRF52832 SoC. Where can I find them? In the Product Specification document they are not given.
Thanks...
I'm looking into the best way to split an application implementing a LwM2M stack over 6LoWPAN between the network and application cores of the nrf5340. I fell like the most...
I have an nRF51 based Bluefruit LE Friend device with the Nordic V3 BLE sniffer firmware installed. I am using the associated Nordic BLE interface with Wireshark 3.2.5 (64bit...
Hi everyone.
I know this is gonna be a long story, thank you for your patience...
I have successfully utilized a few examples in the SDK15.3 directory on my PCA10056...
Hello
I have an interesting problem from the ble_app_uart example modified to work with spis.
ble_nus.c code
In the ble_nus.c code (above) I modified to enable notifications...
