This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
Hi
In my project I have set CONFIG_BT_AUTO_PHY_UPDATE=n in prj.conf. I am using NRF connect sdk 3.4.0
I have configured both central and peripheral to s8 advertising and...
I'm trying to capture a ble connection with nrfutil. What I've done:
- installed nrfutil on my arch based linux machine
- install ble-sniffer
- setup the nRF52840 Dongle...
Hello Nordic team,
I am working with an nRF54L15dk and have an issue using P0.01 as a GPIO input.
P0.03 works correctly with the same GPIO configuration, but P0.01 does...
This is a follow up to case 356908 which was closed due to no resources available. --- We need to shutdown the modem or we end up locking it in the reset-protection state...
Hell there Can I find an SDK that is supported on Nrf52805 chip? Or can I get any proper guidance on program of nrf52805 (the module MS46SFIi) together with Segger Studio...
For regional compliance testing, I am seeking an older version of the Direct Test Mode PC application, specifically v2.0.2 . Is there a way to get old versions of this application...
Hey everyone,
I’ve been banging my head against an issue with my custom nRF54L15 board , and I’m under a bit of pressure to get five samples working. Unfortunately, the...
What is the tolerance of the 0.9V internal reference used by the nrf54L15 SAADC (+/-10%?, +/-1%?), and what is the maximum external reference voltage allowed?
I am using Windows 11, NCS v2, VSCode extension, under WSL2.
What I want to do is build a UF2 image of my zephyr application and be able to drag/drop it onto a bootloader...
Hello Nordic Support Team,
We are developing a custom product based on the Nordic nRF54L15-CAAA(R) SoC.
Our project requirement is to use the nRF Connect SDK Bare Metal...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hi Technical Support, We are using nRF54 series with NCS v3.0.0, and we have encountered a low power anomaly as described below: Configuration: SoC: nRF54 series NCS: v3.0...
Hi,
I would like to know how to ensure that AP-protect is disabled for application based on 17.1.0 nRF5 SDK.
I've understood that the procedure is:
1. recover the device...
We are designing an nRF52840 (Ebyte E73-2G4M08S1C module) into a battery-powered wearable, USB device only, Full-Speed, sink-only Type-C with 5.1 kΩ Rd on both CC pins. We...
