dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
I have a nicely working application that occasionally hangs. I have managed to trap a "hard fault" under the debugger (using VS with GCC). I have the system halted with the...
hello, Nordic developers!
I needs help develop rnf52840.
Goal
My goal is ble & 802.15.4 mutiprotocol, not using zboss network.
Actually, It is the same situation as...
Hello,
I am in the process trying to send multiple packets over ble but cannot seems to figure out this UART example.
I have read many posts that use ` ble_nus_string_send...
My understanding is that the nRF52840, which is the only nordic device to support the long range bluetooth physical layer. Additionally this chip requires SoftDevices 140...
Good day,
We are planning in developing our own custom-made nRF52840 PCB using the reference schematics provided by Nordic Semiconductor.
In the initial phase of our...
Hi,
This is more of a bug report than a question, but not sure how to get in touch with engineers outside the forum.
In app_util.h (Using SDK 12.3.0) there are two...
(nRF51 SDK v12.3.0)
The function gcm_init() in gatt_cache_manager.c (BLE Peer Manager Lib) calls ble_conn_state_user_flag_acquire() part of the BLE Connection State Lib...
Dear Nordic,
I bought three nrf52840 dongle.
How i test the mesh i am totally confused how its programmed and how mesh tested with this nrf52840 dongle can you help me...
We are trying to do final optimization of the load capacitors connected to the 32MHz crystal on the nRF52840. A value of 13pF for both capacitors results in a frequency that...
Hi,
Using SDK 15.0 via legacy nrf_drv_power, the nrf_drv_power_sleepevt_init causes fault:
It calls nrfx_power_sleepevt_enable but never calls nrfx_power_sleepevt_init...
I am working with Thread on the nRF52840 and have setup a few nodes and a Border Router 1.0.0 as described in the documentation using Raspberry Pi 3B+.
My sdk is nRF5_SDK_for_Thread_and_Zigbee_v1...
Hi
I was wondering if it's possible to scan for both 1MBPS and CODED at the same time, or should I initiate 2 different scans.
using this configuration initiates error...
