Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
I am new and trying to install and run samples on Raspi 3B but cannot. Have anyone worked with Raspi 3B and nrf52840 dongle and please give me some instructions.
Hi I'm using Android Studio 3.2 and github.com/.../Android-nRF-UART My Samsung SM-G570Y (Android 7.0 API 24) works no problems but the Samsung SM-G955F (Android 8.0.0, API...
Hi. I am developing a gateway using SDK15 and nRF52840.
I'm advertising 4 devices every 20ms.
Theoretically, it should be scanned 50 times each, but in reality it is...
I tried to add an additional characteristic to NUS service as below.
However, any mobile apps could find only existing Nordic Rx and Nordic Tx characteristics, other than...
- Go to the following link:
www.nordicsemi.com/.../
- Scroll down the page and click the "Downloads" tab
- Go to the nRF52840-DK-HW tab and click "Download file"
...
Dear Nordic Team
-> what is the pinout of the TRACE connector of the nrf52840DK (PCA10056) board ?
I need to connect wires onto P0.11 and P1.00 GPIO, and the trace...
I'm using the nRF52832 SoC through Rigado's BMD 350. For initializing BLE, I'm using the Thingy52 firmware code as the hardware mostly reflects that of the Thingy52. My hardware...
Hi,
I am using nRF_SDK_15.0.0_a53641 and writing a program with keil.
I am receiving data from the sensor with TWI communication and writing it to the sensor by SPI communication...
Hi everyone,
Device : nRF52832
SDK version : 14.2
Softdevice : S132 v5.0
I am facing a problem when changing the interrupt priority dynamically. Let me explain the...
HI,
I'm currently working with two chips RF24L01+.
Each chip switch in sending role to receiving role several times. By default, I set them in sending role and I whait...
Hello
Previous projects used SDK11 protocol stacks with BootLoader and DFU
About the BootLoader of sdk11, DFU is different from sdk15. Please consult me. Thank you.
...
Hi Sir,
As check below link, we know how to re-write the bootloader address.
https://devzone.nordicsemi.com/f/nordic-q-a/26300/how-to-use-nrfjprog-to-write-uicr-bootloaderaddr...
Hi,
I am implementing an application where I need to transfer a 32 byte array via NFC. The only issue is that existing modules in nrf52 sdk have support for UTF-8 encoding...
Hi,
I am looking for a flasher that can be used for nrf24le which can be used in serial production. I found segger Flasher portable plus for nrf51, This device can work...
HI, team.
I use two nrf52840 PDK run the example light switch, light switch proxy server and client.
for the light witch proxy client, when press button 0 it will call...
