Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Good afternoon,
I'm trying to test PCA10001 eval board power consumption and consumption is about 4mA when it should be considerably lower.
To proceed with this measurement...
Hello !
When i was trying to configur my SPI, I observed that there is a difference between the position field announced in the nrf51 reference manual v2.1 and the nRF51_bitfields...
We are looking for the sample software for transmission of nRF2726 (nRF24Lu1P).
nRF2726 does not carry out transmitting operation in enhanced_shockburst_ptx_nrf24lu1p.uvproj...
What I've been observing here is a curious issue under some very specific circumstances. First off, I am using a Xuntong Tech PTR9018 module (this is QFAAC0), the S120 1.0...
Hello all
I making some device with ARM core CPU with nRF51822.
I set CPU to SPI master and set nRF51822 to slave.
And then I read some data from nRF51822, that was...
I am Merging 3 firmware s110_nrf51822_7.0.0_softdevice.hex, ble_app_beacon.hex and bootloader.hex to Output1.hex as follows.
mergehex -m s110_nrf51822_7.0.0_softdevice...
I'm trying to use the Bond ACI command on my nRF8001, but I'm having trouble using it as per the datasheet.
When I set the Timeout parameter to more than 30 (0x001E), the...
The documentation for the nRF51 says only code from code region 0 can execute the erase and write command on code inside code region 0. This means that my bootloader in code...
I flashed S110 softdevice and ble_app_hrs application to nRF51822 on PCA10005 with nRF6310.
and then I tested by nRF toolbox on iPhone5s.
But ble_app_hrs application seems...
I'm attempting to implement a buffer in flash using the persistent storage module but have hit a bit of a wall. When I manually set the block size to something less than the...
Hi,
i'm developing an app for Android and iOS that needs to comunicate with a devices based on nRF51422 with S110 v7 loaded.
We want to encrpyt all comunication and enstablish...
Hello All,
I would like to implement static pin on my sensor. Remember how some Bluetooth Headsets are hardcoded to '0000' I would like to implement '123456' since BLE...
Hello all,
I am using nRFgo motherboard(nRF6310) and nRF51422 DK(s310) and
MDK_ARM(keil Version 5 IDE) to build the sample code.
It seems workable to program and download...
