I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
I have a custom board that started life based off of RF9160-DK 1.1.0.
We have a single programming header that can be used to program either the 52840 or the 9160 depending...
I've installed nRF Connect for VS Code Extension Pack v2024.9.5 to ubuntu 22.04 and after opening vscode the free disk space continues to diminish and cpu load is constantly...
Hello,
We are working on an integration between a nRF52832 and ST LIS3DH accelerometer on our custom board, using SDK 15.2.0 with SoftDevice and BLE enabled, and have observed...
The last couple of months I have been following the course “nRF Connect SDK Fundamentals”, but I am unable to get further than Exercise 2. This is because Visual Studio cannot...
Hello,
I’m having issues with time synchronization when using the sidewalk Sub-GHz template from SDK v2.5.0. My setup includes a Nordic Semiconductor chip nrf52840 and LR1110...
What is the reason for the default 320 hour setting for periodic Tau timer? This seems like an awfully long time, and we're wondering if this is simply a placeholder, or if...
Hi. I'm finally bought a PPK2 to test some of self-built IoT devices. I do have a question in regard to the device (before I break anything). Does it offer any types of short...
Hi. I tried using the TWI master and slave drivers on 2 different nRF52840DK boards. The 100KHz frequency is perhaps a little high and I will see how to lower it by acting...
HI ALL,
I want to create a static library in the application layer, but this library will contain nrf related header files, which will cause cmake to not compile properly...
We have a custom board based on the nRF52805 and we're seeing some odd behaviors in debugging / testing that we're trying to nail down. Two questions:
The INFO.VARIANT...
When I use the J-link programming program, the following happens to the J-flash connection chip
SEGGER J-Link Commander V7.67d (Compiled Jul 5 2022 16:15:35) DLL version...
Hello, my custom board is using pin 09 to communicate through uart. I want to check that uart is working on this custom board. First, I tried to create a simple uart application...
I am using NCS v2.8.0.
After successfully running the headset example with one gateway, one left channel receiver and one right channel receiver am trying to get the Auracast...
I spent quite some time trying to understand why I was getting random network disconnect after a totally fine CEREG notification, like in this log:
It turns out that inside...
Dear Nordic:
Light bulb project support 52840DK, can light bulb project support 52840 dongle? I have not found dongle option in l ight bulb boards folder, only find nrf52840dk_nrf52840...
