Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
I just bought a new laptop: IdeaPad 3 15IAU 7 running Windows 11 and I try to use it and the "nRF Connect for Desktop v5.1.0" and its "Quick Start" option to communicate via...
Can you please help us to convert following snippet from dts to mp_static.yml to use it for DFU applcation. We have external nand flash which used with littlefs and internal...
Hi all,
I have to measure the frequency of a PWM signal routed to one of the nRF52840 GPIO pins.
The signal frequency is ~3MHz.
The measurement is done with the help...
I am encountering the error message " <err> net_pkt: Uncontiguous data cannot be linearized " when already connected with nRF7002-DK to a Wi-Fi network using the EAP-TLS authentication...
I'm following the nordic academic courses, which are very nice by the way!
I've now followed three topics and I find three different variants which confuse me a lot: ...
Hi there,
So in my previous posts, I have been asking questions about setting i2s on two nRF devices in different modes. I have been successful in making it work.
...
Hello,
is it possible to read UICR at address FF8000 from a non secure application for nrf(160.
If yes, can you provide sample code and CONFIG to enable in prj.conf. ...
Hi,
I’m currently working with the nRF9151DK and using the nrf_modem_lib to test some AT commands. However, I’ve encountered an issue with the SIM.
When executing the...
When using the SPIM4 at 8 or 16 MHz, the clock looks nice and even. But at 32 MHz it consistently skips a half beat on the 16th clock pulse. In other words, while all the...
I am working on nRF54L15 and I want to store some user data in flash and for that I want to define the partitions.
I have selected the Target: nrf54l15dk/nrf54l15/cpuapp...
I am running smp_svr demo on my nrf54l15DK board, and use mcumgr command on my linux.
I could connect to my ble device and echo hello successfully (via peer_name='Zephyr...
Body:
Hello Nordic Team and Community,
I am working on a project using an nRF52840 chip on a custom breakout board . I am not using any pre-made development boards or...
During the testing phase of my device I use the Zephyr (uart) logging module and the Zephyr shell module(CONFIG_SHELL_LOG_BACKEND=y). Shell is mostly disabled, and is enabled...
I followed the migration guide for NCS 2.8.0 here for a custom board with engineering rev B silicon. After doing so I can't flash the board anymore and it gives me this error...
