Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
Hi everyone,
I am having problems in getting the low power mode in SAADC to work.
If I enable it in the config file then the ADC doesn't run anymore.( Blank in the RTT...
HI
I've successfully executed the Light control example and remote provisioning example separately but would now like to combine the light control example with the the...
Hello!
i am testing the nrf52 ble uart example. i am able to communicate with the BLE smartphone application (rx and tx) but i cant seem to get printf commands to print...
Has anybody created a table of what SD consumes in term of Flash and RAM.
More specifically I need the resources taken by S332, which include BLE and ANT + DFU.
Regards...
we need to open uart 30s and close it 30s.there is our code:
if(sec_cnt==30)
{
//printf("sec_cnt=30 is now\r\n");//zzq
nrf_delay_ms(100);
nrf_drv_uart_uninit(&m_dtm_uart_driver...
hi
I write a function getT() to read spi thermalcouple chip.
if the function getT() is called in main() function, it will work correctly. Hence, I think that getT() is...
Hej allesammen!
I'm having trouble with the bootloader example "bootloader_secure_ble", which seems to stuck when calling nrf_dfu_mbr_init_sd. But one thing after another...
I'm using nRF5_SDK_14.0.0_3bcc1f7 and SD132 v5.0.0. In response a DATA_LENGTH_UPDATE_REQUEST event, I'm calling sd_ble_gap_data_length_update as follows:
ble_gap_data_length_params_t...
Hi,
I am using nRF52832 with S132 softdevice and SDK version 11. I am getting bad memory address error code.
err_code = sd_ble_uuid_vs_add (&base_uuid, &ble_service->uuid_type...
Hi
I have a softdevice assert problem when i run the "nrf5_SDK_for_Mesh_v0.10.0-Alpha_src\examples\light_switch\client\light_switch_client_nrf52832_xxAA_s132_5_0_0.emProject...
we use
peripheral: exemple ble_app_blinky
central: exemple_ble_app_bliky-c
Instead of a button we have a Switch.
When we set the Switch to "on" the led go on.
That...
Hi, I made a device with using NRF51822, named 'allb' the wearable device for babies.
http://myallb.com
We're planning to make a new version of it with using nRF52840...
The firmware used operate properly in the past, but it no longer does after we replaced the MCU(nrf52832).
During SOFTDEVICE_HANDLER_INIT, the MCU is stopped.
The previous...
I am working on a peripheral. This peripheral is IO display only. On the other side, the central is keyboard + display. I have a single, custom service with a single characteristic...
