Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hi Nordic Team,
Previously, with the nRF52840, we could use the internal ADC channel to directly measure the supply voltage (VCC) for battery monitoring without external...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hello,
I am working with the NRF5340dk, nrf7002ek, and PPKII. I am unable to get the DK to power up with the PPK. I used a knife to break the trace but for some reason...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Somehow a program I have running on a nrf52840-DK board will enable protection. This kind of screws up the small application I am testing because it seems to lock out the...
Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hey,
We're are newbies with Nordic and are trying to program BLE HRS example code to run straight on the nRF52832 (instead of the PCA10040 target).
In order to do so we...
Hi everybody! I am here again bothering you with probably silly questions. I have, on my smart beacon kit, an application that uses an ADC and then sends the converted value;...
`Hi Guys,
My project requirement is that first time i have to bond and connect my nRF8001 BLE with peer device, once connected i have to find peer device address, after finding...
Hi everyone,
I was not able to find a full example in the SDK or online on initializing ANT to work with burst mode. Also, I was wondering if it's possible to setup ANT...
Hello,
I have a design where nrf51422 works as companion chip together with an other uC as main controller (STM32F4).
I need to reset the NRF from the main controller...
Hi,
For our new product we are using nRF52832 chip for BLE and NFC. We have a query regarding the NFC section which is listed below-
Please refer the recommended EMC filter...
I have captured the ble packet showing as the screenshot by using the ble sniffer(win7 ) and wireshark.
But I did not understand the meaning of delta time (such as end to...
Hello!
I would like to whitelist a peripheral when -60 dBm RSSI is achieved (this means that central will bond to peripheral by proximity) but later data exchange must...
Hi all, i have an application with a smart beacon kit; i won't resume the whole project because it's long and boring, i will just say that i have a service that every 100...
Hi,
I'm using the S110 v8.0 on a nrf51422 together with our own scheduler with a few lines left from SDK v8.1.
I'm sending out advertising containing some extra data and...
Dear
As far as I know, the nRF51822 has the Pin Crossbar feature that weu can chose and connect
any GPIO pins as second UART.
I need to talk to two UART peripherals...
Hello Everyone,
I have created an schematic for m custom prototype using NRF51BLE with Sigfox Radio chip whenever i press the button on the NRF51i has to send message to...
Hello,
is there a trick, how the Radio peripherals device address match feature could be used to implement those advertising filter policies that filters based on the PDU...
I want to program the ARM MCU in the nRF51822 Development Kit for my own purposes and then send the processed data using the BLE module in the kit to another nRF51822 Development...
I have been using this mode to init the app_uart_fifo code on SDK8 for a while now and when moving over to the SDK11 code I was in the app_uart_fifo.c code and it's radically...
