Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
A quick one, where do I find a list of the err_codes? I have had a look in the documentation and I was expecting to find a table of them, but I couldn't locate one.
Thanks...
Hello!
I am trying to send a notification to a peer device when a certain event occurs. To do so, I'm using the same procedure as with every other characteristic with enabled...
I used the example of the ble_central\ble_app_uart_c and ble_peripheral\ble_app_uart.
It seems no problem for operation when I check only this example.
But I modified this...
Hello Everyone ,
I ahve deveoped the custom board using NRF51SOC and i have flashed the custom board by usign P20 Connector referred below figure now i would like to debug...
If I let the SoftDevice write to my variables directly by having the characteristics point to my app's variables through BLE_GATTS_VLOC_USER - when are these variables actually...
HI,i have some problems about RSSI (51882)
BELOW IS MY CODE. who can tell me why I can not get RSSI from variable t
int main(void)
{
uint8_t *p;
uint8_t t = 0;
...
Hi,
In S130, both central and peripheral modes are enabled. How do you enable just the peripheral mode and not the central mode for S130 so that less RAM space is used...
I am just working through the tutorial on radio notifications and imported "ble_radio_notifications.c" to my application folder and included the header in included directories...
I use NRF51822 Bluetooth 4.0 e-val kit.
souce code is peripheral example.
so, android smart phone and NRF51822 is connection.
result, Pairing success. occur On_ble_evt...
Is it possible to detect a bluetooth (BLE) enabled phone when it enters the room?
I like to use the nrf51822 (BLE-Peripheral or BLE-Central) to detect any phone when it...
Is it possible to have S110 but not more than ~30-40K size? I need to establish communication in order to upgrade firmware over BLE (UART Emulation), but without using such...
Hello,
Situation:
I am trying to write a characteristic to an iOS device acting as a peripheral from a nRF51822 board.
The board has 2 leds (green and red) and a button...
What is the file pstorage_platform.h? Is it an SDK file? Where does it come from? Is it auto-generated somewhere or should it be just copied from an example?
Hi all,
About the NRF_UARTE0 of nRF52, I want to check the number of received data(example:I set RXD.MAXCNT=16, but I just receive 10 bytes now.Then I want to handler these...
Hi,
I'm working on nRF52822 device with gcc4.9.3 compiler under eclipse environnement (with gnuarm toolchain plugin).
I have some problems with data initialisation....
