NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
I'm implementing a Eddystone beacon ( github.com/.../eddystone ) with the 3 specified frames and it works quite ok with changing the advertising data before transmitting by...
Hello,
I am trying to use the new bootloader provided in SDK v6.1.0 with SD v7.1.0 and MCP v3.7.1. I have loaded the unmodified project from nrf6310/device_firmware_updates...
Hi,
In order to use new nRF51 SDK v. 5.1.0, we have just bought a new NRF51822 EV Kit from your distributor. It contains PCA10001 v2.2.0 2013.49 but the IC is nRF51822...
I am trying to pair nordic with an iPhone app. (using lightBlue) but not device_manager_evt_handler is not getting called
Here is the code, Is there anything else that...
Hi,
i need select bluetooth chipset,but it should support options below;
-Minimum baud rate should be 300 bps,
-It should support 7,8 data bits,
Which can i choose...
Hi
I try to write an application in C# with the MasterEmulator dll (Version 2.1.12.6). It works with the dongle, but not with the nRF51-DK. I can open the Device but I...
Hi,
I am planning to use nRF52832 for one of our projects. Can you please help me with the SDK that will support IAR Embedded Workbench.
Thanks & Regards, Yaron
I've just started working with Nrf51822, I'm trying to make this scenario for weeks but i failed.
Plz help me!
How to make Nrf51822 wake up by a button click, increment...
Hi,
I have 9 BLE devices nearby. I start scanning and all the devices displays in nRF Master Control Panel. However, the scanner then ignores 7 devices and updates RSSI only...
I'm getting the multi-link example working (device manager) with S130 SD and I noticed that the following define is in S110 and S120 but not in S130. I'm looking in the SDK8...
I've create a custom service with two characteristics. I need that the values of these characteristics are notifying at the same time. Is it possible? In this case, one of...
Peripheral role blue-tooth device, linked one phone.How to get phone address? such as phone's bluetooth mac address or something like that.Thank you!
note: device use softdevice...
