I'm working on a IoT device that leverages the AWS IoT and AWS FOTA components from the nRF Connect SDK. The device is battery powered, and so I want to limit the connection...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Hello, just like the title indicated, I need help with setting up the nRF21540 EK with the nRF9160 DK.
For my application, since the nRF9160 DK has the nRF52840 on it, I...
Hallo.
I am working with Thingy.91x and after learning almost all lessons with Nordic Dev Academy, LTE fundamentals, i have encountered an issue.
Right now I can't use...
Hi，
In Core Specification v5.4, there is support for Non-Connectable and Non-Scannable Extended Advertising (ADV_EXT_IND) without AUX packets. However, when using Nordic...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi,
Our project need 7 seperate PWM outputs, as the nRF52840 have 4 hardware pwm, I decide to use GPIOTE with PPI to create extra 3 pwm outputs to drive Red/Green/Blue...
So I am trying to figure out what i do and dont have access to as far as flash and ram is concerned. From the nRF51822 spec it discusses this in general but im finding myself...
Hi
My name is Bernard Britton from Trinidad & Tobago and I am looking for someone competent with nRF9E5 to develope a wireless potentiometer position sensor with LCD receiver...
Hi,
While the softdevice is active (nRF51822) available interrupt priorities are:
typedef enum {
NRF_APP_PRIORITY_HIGH = 1,
NRF_APP_PRIORITY_LOW = 3
} nrf_app_irq_priority_t;...
Hi all,
I'm trying to use NRF24L01, using REUSE_TX_PL command,
the data sheet says as long as CE keep high, the chip will transmit the payload continuously, what i wondering...
Hi
Did you have tested the power current of nRF24LU1 when RF was off and USB worked normally?
We want it less than 4mA. Could you have any idea to make it? Thanks.
Hello! I am trying to develop on the nRF51822 eval board as called PCA10001. The programming interface I use is uVision4 on win7.
I would set a static PASSKEY for the pairing...
When I successfully bond with an Android device, then disconnect the Android device, the following attempt to re-connect fails. It appears the chip enters some internal error...
Hi,
after i get eclipse to debug (thanks to cocoa) i need to make a new project. What option i have to choose, to create a new project to run it on my nrf51822 evalboard...
In the nRF51 reference manual, page 59 shows the config value for pullup is 2 (upshift by 2)
In the file nrf51.bitfields.h, at line 2339, we have:
#define GPIO_PIN_CNF_PULL_Pullup...
Hi,
I'd like to add some custom data (25 octets) to the nRF8002 advertisement packets, using the vendor specific data type (FF).
Is this possible in some way or do we...
Hi, I am trying to enabling a notification of an attribute(once the attribute changed, the server will push the new value to the client) and I learned I have to first configure...
What's the proper way to implement bonding that depends on proximity (rather than a whitelist)? So when the client (phone) is close (say, five to ten centimeters) to the server...
I download uart sample from Nordic developer zone . at devzone.nordicsemi.com/.../is-there-a-serial-port-profile-for-ble
Because you had build the uart profile and iOS...
