Hello,
I am trying to control a PPK2 using my Raspberry Pi 3B+ running a 64-bit image of the Raspberry Pi OS (Debian Bookworm port) and I've been using python (v3.9) with...
I am new to the nRF52840 and the whole Nordic environment, so this may be a pretty basic question. I couldn't find any other blog entries that fit.
I am developing a manufacturing...
We are using BLE and QSPI at the same time and want to have maximum RF range. Sensor data is collected, encoded, and written into flash via QSPI. This goes on for a few minutes...
Hello, we are testing the LPUART example in loopback with a very simple circuit. The carrier module is PAN1780 - nrf52840 on a custom board with no other things connected...
Im currently using a nRF9160 with SLM application as a modem on a nRF52840.
How can I configure the modem for NB-IOT or LTE by using the nrf52840?
My project is working...
Hi, We are using nrf9160 and building the application with CMSE. When my program accesses dynamically requested memory (address 0x200128b0), the program automatically jumps...
Dear all,
I used till now an application to route BLE data over serial port through the dongle USB nrf52840, SEGGER IDE and 1.9.2 nrf conneck. All works well.
Now I'm...
Hi everyone,
I tried the DTM example from / samples/bluetooth/direct_test_mode/src , it work well,
but once I added "CONFIG_BT=y" in my prj.conf file, and testing the...
Hi eveyone,
I try to using ncs DTM example , but I get error reset with following message. what is the meaning for MPSL ASSERT: 2, 80 , I cannot found any related info...
How do I get to the point that I can print a simple "Hello World" on a terminal from a custom board?
I have a custom board the is based on the nrf5340. Specifically, I am...
Hi,
we are working on a nrf52840 based device, which has an external mx25r16 flash (via SPI), having 3 partitions for: secondary-image, mcu-scatch-partition and application...
I am using the nRF9160 with the SLM application.
The device will open a TCP connection to the server; the server will always initiate commands and the device reply. So the...
The informational section of Lesson 6 uses the "Controller/Target" nomenclature for I2C devices, but question 2 of the Quiz requires the use of "Master/Slave" nomenclature...
Hello,
I'm trying to achieve a rather simple program with three steps.
I initialize the SAADC to sample three channels (currently I only have one setup)
I "arm/prepare...
Hi,
In NRF52840, We use LFXO Oscillator (KJ3270001). We did not connect any crystal or Oscillator for HFCLK.
1) What will be the clock source for SPI and I2C communications...
Hi,
We've been working on taking the distance measurements from the nrf_dm sample and displaying them on a waveshare e-paper 2.13 in display. We've been able to get both...
Hi there,
One of the functions of the DECT MAC layer is to allocate radio resources to RDs. According to the standard, the MAC layer does that using special beacon messages...
Hi,
I have a project for nRF52 in VS Code. The project was able to compile and everything worked fine. However, after about a month, I reopened the project and now there...
I am developing LTE-M software on nRF9160. Previously, I checked that it runs well with nRF9160DK. Now I try it with my own board.
First, only for testing, I made following...
Hi, I'm trying to set up wireless audio stream using 2 nRF52832 Dev Kits and SGTL5000 audio boards. SDK: nRF5 SDK 17.1.0 For the wireless protocol I've used ESB, and the program...