Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
i have a code base which is originally run on nrf52832 dk and i want to port it to the pca10059 dongle i run in gcc env and successfully modified the definitions and includes...
Hi, I'm developing an project based on ble_app_uart example. My expection that is multi mobile phone can connect with my nRF. But, my nRF can connect and communicate with...
Hi Nordic! I'm using the nRF9160 with a micro sd card so I have a lot of storage. I was wondering if it is possible to retrieve a .hex file and flash it using LTE?
I'm able...
Hi,
When I try to build a 'light_switch' project on SEGGER embedded studio for nRF connect SDK 1.9.1 for BMD-330-EVAL board. Running into the following error
arm-none...
Hello Everyone,
I am using NRF52833 in my project and I have my NRF module connected to 2 other microcontrollers on UART peripherals. The details are mentioned as below...
We have first worked with a development kit from Nordic (nRF52840 DK) . We flashed the BLE applications using the nRF Command Line Tools.
https://www.nordicsemi.com/Products...
Hello,
I have to open a new discussion session on the same topic because the current session has been closed.
The topic is as follows: devzone.nordicsemi.com/.../at...
Hi,
We currently have a Gazell project that runs on nRF52832 . We have difficulties changing the project target to the nRF52810 .
From the SDK17.0.2, example: "gzll_ack_payload_device_pca10040...
Hi,
I have a firmware (performing DFU over Bluetooth )that runs well on nRF52833 dev kit and for developing the DFU over BLE. I follow this tutorial
https://devzone.nordicsemi...
Using SDK 17.0.2 I wrote a function to modify advertising interval on the run. The function doesn't return any error but the interval isn't changed. What am I doing wrong...
After nrf_drv_twi_tx() function and nrf_drv_twi_rx() function, m_xfer_done is checked using APP_ERROR_CHECK(m_xfer_done). What is the significance of checking m_xfer_done...
Hi,
I am working on DFU-OTA example on BLE. my doubt here is once the controller copied the image into slot1 bootloader will immediately start to validate whether the image...
I am using the following code to generate and output a n-MHz clock on a GPIO pin. (code is borrowed/copied from another question on this forum)
However, the clock output...
I download the zip file(nrf-command-line-tools-10.15.4_amd64.zip) in the website.
And then I unzip it get the following structure files:
JLink_Linux_V758b_x86_64.deb JLink_Linux_V758b_x86_64...
Hello everyone!
Long story short, we are developing a BLE application based on the Nordic UART peripheral example. The board (STM32 micro + BL652 BLE module w nrf52832 inside...
