Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
Hi,
I see in the nrf9160 1.2.0 AT document there is a command XFILEWRITE that suggests the GPS almanac can be written and persist in the modem.
Can you provide more documentation...
Hi, I have developed firmware on nRF52840 as a peripheral. Now I have to develop firmware on nRF52832(beacon) as central which scans the first device and connects and sends...
Hi,
I am using Zephyr configured to use the softdevice as the BLE controller.
I am looking to read and write a small amount of data to the flash for non-volatile storage...
I use nRFgo Studio 1.21.2.10 and J-Link V5.12f.
In nRFgo Studio I can erase my nrf52. However, programming with softdevice or application ends with error Unable to find...
Hi,
We are having custom HW and having NRF91DK and NRF52.
We have architecture as NRF91 and NRF52 (Central) is connected over UART and NRF52 (Central) and NRF52 (Peripheral...
Hi
I'm using direction finding connectionless_rx project from NRF Connect SDK 1.7.1 with NRF52833 and I want to sample the CTE with a 4MS/s sampling rate (sample spacing...
Hi, I have a project developed on Visual Studio Code and PlatformIO. Now I want to use the same classes with SEGGER Embedded Studio. How do i do? Thanks.
I am very new to this product and Bluetooth technology in general. I am trying to determine what I have done wrong. I have purchased the nRF52 dev kit and downloaded and installed...
Hi,
In our design we use Fanstel BM832 module, based on nRF52832 chip. We have failed spurious emission in ETSI RX mode. Rx LO at ~4958 MHz exceeds the limit by 0.3 dB....
Hi,
We are working on the iOS App development for our BLE device. Our query is that, “we have completed the connection with Ble device with our iOS application on first...
I am using a setup with a PCA10040 with the PPK as piggy back. I also use a JLink Ultra+ connected to the "Debug in" connector on the PCA10040. I have cut the SB20,21,26,27...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I had tried to advertise in TLM format (in temp variable) of eddystone value coming from sensor ssts751 integrated with my devkit but not getting correct. Please suggest me...
I use nRF5340 DK as Central, iPhone as Peripheral.
I start a scan with no filters and in scan_filter_no_match() I check if RSSI is good enough " RSSI > -40 " and initialize...
Hi all,
I am currently developing on the development board nRF52832, SDK16.0 and SD132v7.2.0.
My development board acts as a slave, while an app that tries to connect...
