S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
We need a simple program that can be used as a terminal program on Windows (with nRF52840 dongle attached) to a remote device running the BLE UART service.
Essentially,...
I would like some guidance on how to start a project using the nRf52840 - i.e., what sample programs would I start with? The project is a remote control lighting application...
I used the example pin_change_int from peripheral examples and commented the OUT pins. In addition I added the sleep commands to the main while loop. This is the code:
...
Hello everyone,
I'm currently working on a project that requires a nrf52832 chip to relay raw beacon data over UART to an esp-12F module. I am having a difficult time figuring...
Hi.
I have NRF52 DK.
I have successfully flashed TWI sensor example on to the board.
However, when I move forward with other projects in SDK like ble_app_uart and ble_app_blinky...
Hi I wanted to ask if there is a driver/library for the mcp25625 chip? Also for the communication do I use " SPIM — Serial peripheral interface master with EasyDMA " or "...
I'am achieving lowest power consumption in connected mode. I can't identify source of short spikes every 40Hz when mcu is in low power mode. I'am sure that it's not application...
under code is my sdk main code and i want to change code to Sensor --I2C-- nRF52 --UART-- app but where i have to start and change ?
/* Copyright (c) 2010 - 2017, Nordic...
I've been doing some testing with Mesh DFU and I've noticed some unexpected behavior around handling missing data segments.
As I understand the Mesh DFU protocol, if a data...
I have issue about calibartion using saadc.
I use 52832, S332, SDK 15.3.0
when calibration is excuting, ANT+ and BLE is also doing.
I use low power mode in saadc.
...
Hi
I want to know if there is any source code of thingy91.
Because I want to follow thingy91 for making a product with the use of the same antenna, and I want to know...
Hi,
Recently, I was trying to move my project from STM to Nordic IC.
I just wonder how to implement the below codes into the nRF52832 or how to program it in Nordic environment...
Hi,
I want to set sending power(+4dBm) of NRF52810/NRF52832 with SDK 15.0.
Now,i find i should use the order of sd_ble_gap_tx_power_set(uint8_t role, uint16_t handle,...
Using a AF_INET UDP socket on the nrf9160 I will get ENOMEM when I send a bunch of datagrams over the socket. I understand how there can be a limited number of buffers for...
I am trying to debug the dfu bootloader using SES. This is my first time using SES. I opened the example project and everything builds fine. The image loads on the device...
