S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hi,
I'm trying to interface SIM808 with nrf51822 over uart using nrf_drv_uart. Everything works well for some time, but then uart starts reporting error code 1, NRF_UART_ERROR_PARITY_MASK...
Hello,
I am working with the GPIOTE library to get a GPIOTE_IRQ from a peripheral.
I have several questions regarding the library and how IRQ works.
1.How do I clear...
Hello,
I am using SDK7.1.0 for NRF51822.
In my subroutine, I would like to disconnect with the peer device, and re-advertise. But when after re-advertising, I found the...
Is it possible to set scope for search in info-center only for SDK 11? It search in all SDK versions and sorts results randomly. It is very annoying. Especially when there...
Hi,
I want to build expertise in BLE and want to use the Nordic nRF51x22 to build a hardware and write the firmware for the same.
I am planning to use the nRF51 DK....
I'm calling sd_ble_gatts_characteristic_add multiple times to add characteristics to a peripheral. At some point I get a return value of 0x200020B6. I'm not making much headway...
Hello everyone,
I am trying to use the ble_app_hrs_rscs_relay example from SDK V11 for s130 (2.0.1).
It compiles and works well when I use an pc10028 evaluation board...
If I have multiple services, 2 for example, how should I set up the srdata.uuids_complete.p_uuids in the code:
ble_advdata_t srdata;
memset(&srdata, 0, sizeof(srdata)...
Hello,
I am developing beacon on nRF51DK and I want to store in non volatile memory some parameteres like:
ProximityUUID
Minor
Majnor
AdvInterval
Tx_power...
Is it possible to configure SPI Master API to send multi-byte words?
My peripheral expects transfers in 16-bit blocks (CS goes low, 16 bits are clocked in, CS goes high...
Hi guys,
I'm going to start the development of a new project based on nrf52832 and I have to decide the firmware architecture and APIs. Designing the support for the Nordic...
I am using a digital microphone using i2S interface with the following signals: BCLK (bit clock), WS (word strobe), SELECT (select for Left/Right) and SDOUT (digital data...
I received that error using master control panel version 3.7.1
While using the last nRFgo Studio (1.21.2) it tells me JLinkARM.dll is not correctly installed. Please run...
Hi! I need to sample and send adc values using ble_nus to read it on an android device. I am using nrf 51DK and SDK version 10.
I tried the below two codes but they are not...
I have a NRF24LE1 transmitter transmitting 10 bytes of static payload every sec.
While I have a Receiver which is NRF52-DK. It is receiving the payload that is sent by...
