Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi,
we are using nrf52840 and nrf SDK-16.0. we have achieved simultaneous connection and data transmission for 4 devices in Ble 4 (i.e. 1 Mbps PHY).
Now we are trying...
Hello Everyone! I am working on a zephyr project based on nrf52832_mdk hardware. I have a code that transmits data over BLE. The BLE connection name is, let say zephyr-connect...
Is there a way to modify the PHY layer, or SoftDevice, so that a timestamp is immediately read from a timer and forced into the manufacturer data right before transmission...
I have an application I am working on, and I created a custom structure rx_servo_t. The structure is meant to provide methods for controlling some off board motors via GPIO...
Hi,
We need to integrate a testing mode within our firmware that uses Nordic controller to do BLE functionality as we want to achieve single image solution for production...
I'm working with a BLE peripheral application that must transfer large amounts of data to a phone central. The application uses the MTU negotiation to determine the max notification...
Hi,
I'm evaluating the nrf7002 for use in a monitor mode device. I'm using a nrf7002-dk, nrf connect sdk 2.6.1.
I'm working off of the monitor mode sample here: https...
Hi,
We have several hundred devices in real time deployment and find the typical DNS/Cellular connectivity issues during the day that we generally solve with delayed connection...
Hi there,
I must interact with an I2C slave that sends variable-length messages. The first byte of the transactions describes the length of the remaining bytes.
i2c_write_read_cb...
Dear Support,
we would like to know what is the total value of the capacitance and the inductance of the nRF52805 (for ATEX certification). I can not find this information...
We have project using the common Matter Code base from SDK 1.6.1 and using a variation of the code to act as a switch sensor device time. This seems to work pretty well; however...
I need to add tx power to my BLE advertising, but I need to ensure it is in the Scan Response only not the main AD PDU.
Also, I change the Tx power by code using the function...
I have a PCB made for my project. I want to read log from RTT. When I try the same software in the development kit, I can read from RTT. But when I want to read from the PCB...
Hi,
I have a proyect with the following memory requirements.
The current project has a propietary bootloader and bare-metal application. Therefore there is no Zephyr...
Hallo,
In the BSP startup files for the nRF5340 (gcc_startup_nrf5340_application.S & gcc_startup_nrf5340_network.S) the interrupt vectors USPTn_IRQHandler (n=0,...,3) are...
