hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
To the kind attention of Nordic support team,
I'm running ble_app_hids_mouse_pca10100_s112 in a PCA10100 dev board. It is the sdk17 program, where:
1.I added 2 files ...
Hi there,
We are currently running tests on the nrf9160 DK using an iBasis SIM card, which should be capable of connecting to multiple networks. We are trying to understand...
Hi,
How is the LTE-M or NB-IOT network availability for very much remote locations like forest or mountains for emergency use cases compared to low-earth orbit satellite...
NCS ver: 2.0.1
chip: nrf52840
node: MTD not SED
network: one OTBR as leader and one MTD as child
After about 4~10 hours, MTD will offline. Sometimes it can reconnect...
I like to enable compiling my code with c11 or c17 but when compiling with west this does not seem to be possible.
To force the compiler to use c11, I used option:
CONFIG_COMPILER_OPT...
Hello,
I am experiencing a SoftDevice Controller ASSERT: 62, 1846. I am using a nrf52832 acting as a peripheral and nRF Connect SDK v1.9.1. This assert happens when large...
BLE-app-blinky client not working
BLE-app-blinky sample build success, LED1 on, when connect LED2 on, but i can not see client service uuid in my android app.
i cannot...
Hi there,
We are doing some testing on an eSIM with the nrf9160 DK, and we are looking for an AT command that can be used to read the eUICC ID of the SIM. We are using the...
Hello,
We are planning to integrate the LwM2M carrier library. Our system uses mfw 1.3.3 and NCS 2.1.0.
Based on the following page https://infocenter.nordicsemi.com/index...
I'm trying to update MCUboot from the application. As a first test, I enabled the flash shell commands. I can erase somewhere within the flash without problems:
uart:~$...
Hi,
I have a simple SPI circuit to read data from a flash memory W25Q64 to be exact and I have difficult time reading the device address of the chip through SPI.
The situation...
Hi Devzone,
we are working on nrf5340 mcu, from the DTM sample, l learned that the application run on network core only, but my application scenario is combine the DTM with...
Hello,
I'm using the SAADC voltage conversion formula from the Nordic example as follows: 10 bits are used in the example.
By the way I want to change ADC resolution...
This is a follow-up to my previous post . I'm developing a BLE Peripheral application on the nRF52832 that uses NRF_SDH_DISPATCH_MODEL_APPSH to receive events from the SoftDevice...
I think this is a bug report for the VScode plugin
One of my boards shows this error when I try to debug
Nrf52833 custom board connected with SWD on Jlink
I was...
