Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
Hello.
I am developing with nRF52840DK.
Normally, I think that the buck regulator supplys 3.0V to Interface MCU and nRF52840.
I want to connect the 1.8V peripheral...
We're working on an nRF52840-based project that started development on SDK 17.0.0 and Softdevice S140 7.0.1, but we wanted to get it to the latest release before production...
Hello,
I am working on Arduino's platform and decided to ditch the ArduinoBLE.h library due to its overhead.
I would like to send high frequency (2Mbps per the spec ,...
Hi,
I've trying to get the Omnivision OV7670 to work with the nRF52840-DK. I'm not completely sure whether I've configured it correctly. My pin assignments are adapted from...
Dear,
we have found a strange behaviour when using the DTM in SDK 17.0.2 and 17.1.0. The problem starts from ble_dtm.c:1188 when comparing the parameter value with -30dBm...
Using SDK 14.0.0 with SD 132 v5, the device name I'm advertising with here is "000000DK". But the advertising module is truncating it to "0000". It will do this if I have...
Hello,
I want to use 1M baud rate in nRF5340 DK board.
DK board is connected to USB to Serial.
Until 921600, UART is received correctly. And UART is broken in 1M....
Hello,
I have been using NRF Connect SDK 1.6.1 with Microbit V2 to run some zigbee projects! Now when I should build some new firmwares I upgraded to SDK 1.7.1 and after...
Hello, I have an nRF52840 custom board and SDK 17. I want to make a project with a buzzer control. I am trying to find a suitable sample project to start developing my own...
Hi everybody,
I am working with an UART example with multi-link and everythink working on coded_s8. The objective is keep 20 devices connected and every peripheral send...
Hi Tech support:
I am using the latest Desktop nRF Connect(Windows version) tool. And I want to use it to connect to my nRF52 DK board and setup up an advertising setup...
Hello,
for our application i need to periodically enable and disable the openthread stack on the nRF52840 chip.
For testing purposes i've modified the Thread CLI example...
Hi,
In my application i am trying out to transfer data in Long range BLE_GAP_PHY_CODED mode , i have set my peripheral has to advertise in PHY coded mode below is the advertising...
Hello,
We are using nrf52832 in our development, we recently got the otii arc to measure the power consumption of our device.
During sleep mode we notice a huge spikes...
