Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
We're using the UDP SDK example on the NRF9160DK with modem fw 1.2.3 (10 minute sleep, 0 second active timer), and we're seeing a current of 0.7uA when measuring on the header...
I download 2 projects
1. Zephyr Project 2.5.99
from install to west flash is Done
2. nRF Connect SDK 1.5.99 manully
from install to SES IDE is Done
3. use nrfconnect361x8664...
Hello,
Conf: custom board, custom firmware, SDK16, SD 7.0.1, NRF 52832
When I configure connectivity advertisement with ble_adv_fast_timeout set to <= 180s the advertisement...
Hi guys,
I have a setup to receive the microphone data from the Thingy 52 on an nrf52840 evaluation board. Currently I recive the 131 audio packages ADPCM encodet. In the...
Hello.
There is nRF52840 and nRF9160 on nRF9160 DK.
here are codes on this two chips:
nRF52840: 1:SoftDevice. 2: BLE APP
nRF9160: 1: Modem & GPS firmware. 2: Bootloader...
Looking at PM_EVT_CONN_SEC_FAILED parameters, i.e.,
re: nRF5 SDK v16.0.0, nRF58233, S113
Looking at the definition for pm_sec_error_code_t: “Possible values are defined...
Hi All,
I've had a product (RunScribe) in the market for some time, running on the nRF52832. This was built on the SDK13.1 / and the S332 v4.0.2 SD. All using Keil. As I...
Hello!
I'm planning to start a project with the nrf52832 chip, I mainly choose this product, because of the low power consumptions and ble.
I would like to start my development...
Hi I am using ncs version 1.5.0 and dk version 1.0.0
I just want to try a simple ping test.Is there any at command are sample code is available to check the network connection...
hello i am using nrf52840 with our customised board with sdk version 15.2 i am trying to achieve maximum distance using coded phy with nrf long range demo as my base i have...
Hello. I tried to run ble_peripheral/ble_app_uart example from the newest SDK (17.2) on my ebyte e73 with nRF52833 onboard, but without success. I used softdevice S140 (tried...
HI,
My application needs to send the data from PC(server) to Nrf52840(client) . The length and type of the data are 2758 bytes and char data type, actually data has been...
