Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
Hi,
When running FreeRTOS I'm not able to use the NRF logger module once the task scheduler has started.
I have a low priority task that flushes the logs but whenever...
Context: nrf52840DK, s140, SDK 17.0.2
Hi,
I need to oversample a few ADC pins with burst enabled at roughly the same time periodically: e.g. oversampling 4 separate inputs...
Hello,
I have nrf52832 dev kit and the device. I try to make smaller code size and setup Optimization Level 2 for size.
BLE works, but when connect by NRF connect and...
Hi,
I am currently developing a product which is supplied with battries (chip is nRF52810). Under normal conditions, the product goes into system OFF mode in standby, it...
Hi,
I'm testing a custom board, based on nrf52832_xxab SoC, with a SWD interface. The board was working fine, but suddenly the debugging interface stopped working. Any idea...
I am curious whether there is a correlation in distance between different devices in a BLE connection.
A picture is attached to describe the situation.
A sensor-board...
Hello dear support team, We are in the process of designing an enclosure for our device. The enclosure is going to be molded and we would highly appreciate your support to...
My requirement is to send from Controller Device to NRF Ble Device through UART of 40Bytes at the rate of less than 1ms. Currently I am using ble_app_uart example as a reference...
Hello,
I am working on the ble_app_template example, nrf52840, SDK 17.0.2 and Segger Embedded Studio version 5.34. I have added multiple custom services to my code, however...
Hello,
as part of my project of wearable solderless modules, I've packed the nRF5340 to the same 20x20 mm form-factor - it was described earlier as part of the https://devzone...
Hi,
We have the nRF52811 in QFN48 fitted to a number of products, with the chip showing 'QAAA0 1850AA'. Does this mean that it's an early Revision 1 ? The Errata in the...
Hello,
I'm new in the Nordic sphere and I'm starting in embedded programming. I was confronted with the following problem and I will try to give as many details as possible...
Hi,
got a question about UART and maximum bytes it can receive in one burst or "packet".
Using nRF52382 and SDK16.
Recently I've been developing a new app in which UART...
Hi Nordic Team/public users,
Request your assistance for troubleshooting the NDK-nrf52840 board that was having a detection issue whereby my laptop/PC was unable to detect...
Hello, I hope you are safe and well during these times. I have created a successful prototype using the Adafruit Feather nRF52 Bluefruit and the Arduino IDE. I think I am...
