i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
I have compiled asset tracker example and it worked on 0.8.2 version of board but not on 0.8.5 board.
1) Is there anything which should be made differently in software for...
Hi, I'm trying to measure the current of my nRF9160 DK (PCA10090 v0.8.2) and have some problems. In respect to the following thread (https://devzone.nordicsemi.com/f/nordic...
Hello. Project im developing requires low power wireless encoder. NRF52832 is a really impressive chip that handles everything i need within 40uA. But I've got problem with...
hi, we delevoppe a card with a module which is use your nRF52832 IC. I check in your document information relative to IO hardware, but i didn't find any information concerning...
I am writing some code for a customer using the nrf52840.
The Softdevice asserts immediately after a call to nrf_fstorage_write().
The write address is OK, alignment...
whenever I use nrf connect desktop app in my Linux system for power profilling.
The power profiling kit doesn't start and keeps on giving the same error
There are similar...
Hello team, I'm working on system development using Mesh SDK and I have some questions so please let me know. ############### Development environment IDE : Segger Embedded...
I was able to create 2 times, Timer 1 and Timer 2.
They work when they run separately, but one stops when I try to use both of them.
I need simultaneously running two...
Please confirm the following is correct for nRF52840 (per PS v1.1)
1. The firmware doesn't have to enable internal pull-up when the pin reset is configured (it's done automatically...
Hi,
I am developing a solution with zigbee (nRF52840).
I want some end device is joined to specific router.
In the documents, if end device find more than one router...
Hi, Everyone.
I'm trying to connect nRF52 DK Board to J-link base tool.
But I can't connect.
Wires between nRF52 B/D and J-link base tool are conneted below.
nRF52...
Hi,
I am new in this area. I wanted to use the detect "signal" but it doesn't work as protected. This is my main :
I just try to detect when the detect signal is HIGH...
Hello,
i tried the getting started procedure with the NRF9160DK demo board but I cannot finish the whole procedure.
After activating the iBasis eSIM, I turn on the...
It's may be strange enough, but i can't see the clear answer on this question. What is the limitations for pin function maping? I need to understand which pins i can use for...
Hi,
I am surveying the zigbee example for my project.
In my project, coordinator has to permit or reject certain end device/router.
I have searched following articles...
